A beam having a constant solid rectangular cross-section is subjected to pure bending. The longitudinalstrain at a point A on the cross-section is 3.0 x 10-5. If the Young's modulus of the material of the beam is200 GPa, then the maximum tensile stress (in MPa) anywhere in the section isA30 mm100 mm

Given data, The longitudinal strain at a point A on the cross-section =3.0x10-5 Young's modulus of…

A beam having a constant solid rectangular cross-section is subjected to pure bending. The longitudinal strain at a point A on the cross-section is 3.0 × 10-5. If the Young's modulus of the material of the beam is 200 GPa, then the maximum tensile stress (in MPa) anywhere in the section is A 30 mm 100 mm

A beam having a constant solid rectangular cross-section is subjected to pure bending. The longitudinal strain at a point A on the cross-section is 3.0 × 10-5. If the Young's modulus of the material of the beam is 200 GPa, then the maximum tensile stress (in MPa) anywhere in the section is A 30 mm 100 mm

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter9: Time, Temperature, And Mechanical Properties

Section: Chapter Questions

Problem 9.3P

See similar textbooks

Similar questions

Find the req,
Q- A uniform prismatic circular bar made up of rigid material is subjected to a tensile force of 5000 N at one end. If the diameter of the cross-section is 7 mm, then find the stress and strain in the bar.
STRAIN
Don't give me wrong solution
AN ALUMINUM TUBE IS FASTENED BETWEEN A STEEL ROD AND BRONZE ROD AS SHOWN IN THE FIGURE. AXIAL LOADS ARE APPLIED AT THE POSITIONS INDICATED. FIND THE VALUE OF P THAT WILL NOT EXCEED A MAXIMUM OVERALL DEFORMATION OF 5mm OR A STRESS IN THE STEEL OF 120MPa, IN BRONZE OF 130 MPa AND IN ALUMINUM OF 90 MPa. Modulus of Elasticty of Bronze = 80 GPa, Aluminum = 65 GPa and Steel = 210 GPa. 2P P 3P 4P L = 500mm 800 A = 400mm² 900 600 700 C
The strain of a component, which has a tensile modulus of 3 X 105 MPa, and subjected to a stress of 5000KPA, is .a 0.0000167 .b 0.0000176 .C 0.000167 .d 0.00176
A plate in equilibrium is subjected to uniform stresses along its edges with magnitude o = 30 %3D MPa and ow = 50 MPa as shown in the figure. %3D = 50 MPa %3D O = 30 MPa XX ple The Young's modulus of the material is 2 x 1011 N/m2 and the Poisson's ratio is 0.3. If o is negligibly small and assumed to be zero, then the strain Ezz is
A 3m long steel plate having a cross section of 25mm by 300mm is use as a hanger and subjectedto a tensile load of 1070 kN. The proportional limit of the steel is assumed to be 200 MPa. If thePoisson’s ratio is 0.25, determine the following;a. The transverse strain,b. The total axial deformation, andc. The transverse dimensional change along 300mm.
Steel Stress-Strain diagram. Which of the following statements is NOT correct? Engineering stress is the stress computed using the original area and not the necking down area. The constant stress region is called the yield plateau or plastic range. The linear portion is also called the plastic range. The proportional limit, elastic limit, upper and lower yield points are very close to one another and are treated as a single point called the yield point.
For the state of stresses (in MPa) shown in the figure below, the maximum shear stress (in MPa) is 2 2
1. For each state of plane stress shown below, i.e., for configurations (a) and (b), indicate whether each component of the state of strain is: = 0 (equal to zero) >0 (greater than zero) <0 (less than zero) The material is linear elastic with Possion's ratio is between (0, 0.5), and the deformations are small. T 30 e X 0 Ex Ey Ez Yxy Yyz Yzx (a) (b) 1° (b) 1x
1