A bar of length L tapers uniformly from diameter 1.1 D at one end to 0.9 D atthe other end. The elongation due to axial pull is computed using meandiameter D. What is the approximate error in computed elongation?(а) 10%(b) 5%(с) 1%(d) 0.5%

Let us take, Applied axial pull load = P Young's modulus = E Diameter at first end = D1 = 1.1 D…

Answered: A bar of length L tapers uniformly from…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

K=17 so 107 MPa strength of material question.
A 50-mm diameter cylinder is made of a brass for which the stress-strain diagram is as shown. The angle of twist is 5° in a length L = 725 mm. The three points on the nonlinear stress-strain diagram used are (0, 0), (0.0015, 55 MPa), and (0.003, 80 MPa). By fitting the polynomial T = A + By + Cy² through these points, the following approximate relation has been obtained. T= 46.7 × 10%y-6.67 × 1012/2 Determine the magnitude Tof torque applied to the shaft using this relation and the two equations given below. Y Ty - ρφ T (MPa) 2π ζ ρ?τὰρ 100 80 60 40 20 0 0.001 0.002 0.003 Y d = 50 mm L The magnitude T of torque applied to the shaft is kN.m.
Solve
3) Referring to the plot below, a steel bar with a radius of 0.2523-inch exposes to 650°C. If the expected lifetime of the iron bar is 9 years, what is the maximum load allowed to carry? ( Stress (psi) 20,000 10,000 8,000 6,000 4,000 2,000- 1,000 30 32 34 36 38 40 42 (36+0.78 In s) Larson-Miller parameter w 1000
Solve
A load (P) of 150 kg was applied using a bending strength tester on a rock sample of dimensions (24 cm length). 5 cm in width and 5.2 cm in thickness, find the rock's tensile strength (6t) and bending strength (F). 6:02 PM /
Find the length of elongation of a uniform mild steel rod length of 3 m, cross-sectional area of 150 cm2 and Young's modulus of 100 GPa subjected to an axial tensile (or compressive) force F= 200 N.
A given conical bar is tapering uniformly from 4 cm diameter to 15 cm and has a length of 40 cm. An axial force of 80 KN is applied at each end if the bar, Find the elongation of the bar. Note: Take E=200 GPa
Load (N) Elongation (mm) In a tensile test of stainless steel, the following data were obtained: 7,200 11,250 13,500 16,200 18,900 20,200 20,700 13,200 24.90 0.0 0.505 2.03 5.08 10.16 15.24 21.80 The dimensions of the cylindrical specimen were initial length L₁= 50.8 mm and initial area A₁ = 35.8 mm² and the area at fracture was Ar = 10.0 mm². Plot the stress-strain diagram and determine the following: a) Modulus of elasticity b) The yield strength at a strain offset of 0.002 c) Ultimate strength d) Fracture strength
Q.5) A bar of 1000 mm length and 40 mm diameter is centrally bored for 300 mm length at one end at a diameter of 20 mm. Young's modulus of the material is 2 x 10° N/mm². If the bar is 2 40 mm 20 mm 700 mm 300 mm loaded axially with a load of 30 kN the extension produced is (A) 0.1136 mm (C) 0.1478 mm (B) 0.1313 mm (D) 0.1542 mm
Compute the elongation, in %, of a cylindrical copper rod if it is cold worked such that the diameter is reduced from 15.9 mm to 10.4 mm
H.W 1 A6 m long hollow bar of circular section has 140 mm diameter for a length of 4 m, while it has 120 mm diameter for a length of 2 m. The bore diameter is 80 mm throughout as shown in Fig. B 140 80 300 kN + 300 kN 80 120 4 m 2 m Find the elongation of the bar, when it is subjected to an axial tensile force of 300 kN. Take modulus of elasticity for the bar material as 200 GPa.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A bar of length L tapers uniformly from diameter 1.1 D at one end to 0.9 D at the other end. The elongation due to axial pull is computed using mean diameter D. What is the approximate error in computed elongation? (a) 10% (b) 5% (c) 1% (d) 0.5%