A bar of 50 mm diameter is subjected to a pull of 150 kN. The measured extension on gauge length of 400 mm is 0.6 mm and the change in diameter is 0.005 mm. Calculate the Young’s Modulus of elasticity.

A bar of 50 mm diameter is subjected to a pull of 150 kN. The measured extension on gauge length of 400 mm is 0.6 mm and the change in diameter is 0.005 mm. Calculate the Young’s Modulus of elasticity.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Related questions

Q: 2.3-7 A steel bar 2.4 m long has a circular cross section of diameter d, = 20 mm over one-half of…

A: Given Data: Total length of the bar is L=2.4 m The diameter of the left half portion is d1=20 mm The…

Q: An aluminum alloy cylinder with a diameter of 3 in. and a height of 6 in. is subjected to a…

Q: 1 - An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure.…

A: A stress element is given with stresses shown. Young's modulus of elasticity, E = 80GPa Possion's…

Q: A metal bar of variable cross section as shown and length is subjected to 1000 kN of force. The…

A: Force = 1000 kNSection :Length 1 meter long area = 10000 sq. mmSection 2 :Length = 500 mmArea =…

Q: a bar is 500mm long and is stretched to 505 mm with a force of 50kn.the bar is 10mm diameter.…

A: Given data : Initial length=500 mmFinal length=505 mmForce (F)=50 KNDiameter (D)=10 mm

Q: During laboratory testing of an 8-inch steel-alloy rod with a cross sectional area of 32in a tensile…

A: To find modulus of elasticity and Poisson's ratio

Q: Given that a steel cyInder of dimenslons 12.0 mm in dlameter and 70 mm bng is subjected to tensicn.…

A: a) According to Hook's law within the elastic limit, stress is directly proportional to strain.…

Q: The aluminum machine part is subjected to a moment of 75 kNxm. Determine the bending stress created…

A: Solution:Given: The moment acting on the section is M=75N.m which is sagging, so the topmost fiber…

Q: a. A round steel bar with an initial diameter of 20 mm and length of 2 m is placed in tension,…

Q: A 10.0 mm diameter cylindrical specimen of a bearing bronze material is pulled under uniaxial…

A: given-10.0 mm diameter 1500 N force∆d=0.67 mmn=0.35

Q: 29. During laboratory testing of an 8-inch aluminum-alloy rod with a cross sectional area of…

A: Given:- The length of the aluminum-alloy rod during testing = 8 inch The cross-sectional area of…

Q: A steel specimen of 12 mm diameter extends by 6.31 x 10-2 mm over a gauge length of 150 mm when…

Q: Q2. A circular rod of 500 mm long is subjected to a tensile force of 50kN. The tensile strength is…

A: Solution : Length L= 500 mm Tensile force =50 KN Tensile strength =160 Nmm2 Modulus of…

Q: Consider a cylindrical specimen of a steel alloy 10.0 mm in diameter and 75 mm long that is pulled…

A: the test is conducted in UTM. the test is standardized by American testing society material . the…

Q: A 100 mm2 square cast iron (CI) encased a steel circular rod of 40mm diameter. The assembly is 2 m…

A: Given, 200 kN load applied on assembly E of cast iron = 100 GPA E of steel = 200 GPA Area of cast…

Q: The compound bar containing steel, bronze, and aluminum segments carries the axial loads shown in…

A: Given -

Q: A bar of 30 mm diameter is tested in tension. It is observed that when a load of 80 kN is applied,…

A: Given data:

Q: A 50 mm X 80 mm rectangular steel plate subjected to the uniaxial stress condition is shown in the…

A: Given data Stress in x direction (σx) = 200 MPa E = 200 GPa μ = 0.3

Q: A 20-ft wrought iron bar that is ½ inch in diameter is subjected to a tensile force of 3 kips.…

Q: A cylindrical steel alloy rod with a 0.5 in. diameter is subjected to tension.Determine the…

A: It is required to calculate the strain in the x-direction. Here, is the change in diameter, and do…

Q: 09. The rigid bar of negligible weight is supported as shown in the figure. If W 80 kN, compute the…

A: Given DataW = 80 KNtensile stress in stell rod = 50 MPa (σs)Equilibrium…

Q: has a yield strength of 45 ksi. What maximum contact stress will result from the load ofF = 2600 lb?…

A: Contact stress: - It is defined as a stress which develops when two surfaces come in contact with…

Q: A cylindrical aluminum alloy rod with a 0.5 in. diameter is subjected to ten- sion. Determine the…

Q: A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial load…

A: solution cross section dimensions 0.6 inch ×4.1inch deformation of 0.115 inche over length L…

Q: Q- A bar of length 2.1m and diameter 38mm is subjected to pure torsion. If the shear modulus of the…

A: Length of bar L=2.1 m Diameter d=38 mm Shear modulus G =41 GPa.

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

Q: Determine the Poisson's ratio v.

Q: cylindrical specimen of stainless steel having a diameter of 12.8 mm (0.505 in.) and a gauge length…

Q: Answer all.a.A mild steel flat of width b= 150 mm, thickness t = 20 mm and length L= 6000 mm carries…

Q: ne force that will produce an elastic reduction of lus (E) and Poisson's ratio (v) are,…

Q: PROBLEM 01: Hollow bar length is 1.40m long and tube length is three-fourth as long as the bar.…

Q: A cylindrical aluminum alloy rod with a 0.5 in. diameter is subjected to tension. Determine the…

Q: 1. A circular rod of diameter 20 mm and 500 mm long is subjected to a tensile force 45 kN. The…

A: To determine: Stress, strain, and elongation of the bar due to applied load.

Q: IV. An Aluminum bar AD (see figure) has a c loaded by forces P1 = 7560 N, P2 = 5340 segments of the…

Q: Determine the following for the bar. A) B) C) D) What is the Modulus of Elasticity for the material…

A: Given "

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen with a circular cross section. The diameter was 3 8 inch and the gage length (The length over which the elongation is measured) was 2 inches. a. Use the data in Table 1.5.2 to produce a table of stress and strain values. b. Plot the stress-strain data and draw a best-fit curve. c. Compute the, modulus of elasticity from the initial slope of the curve. d. Estimate the yield stress.
Ques.
A cylindrical bar of steel 9.9 mm (0.3898 in.) in diameter is to be deformed elastically by application of a force along the bar axis. Determine the force that will produce an elastic reduction of 3.0×10-3 mm (1.181 ×10-4 in.) in the diameter. For steel, values for the elastic modulus (E) and Poisson's ratio (v) are, respectively, 207 GPa and 0.30. i N
) Consider a cylindrical specimen of a steel alloy 10.0 mm in diameter and 75 mm long that is pulled in tension. (a) Determine its elongation when a load of 20,000 N is applied. (b) What is the modulus of elasticity? (c) What is the strength at a strain offset of 0.002? (d) What is the tensile strength?
During laboratory testing of an 8-inch aluminum-alloy rod with a cross sectional area of 0.32in, a tensile load of 40,000 lbs.is applied. If the cross sectional area decreases to 0.3188in and lengthens to 8.021 inches, what is the Modulus of Elasticity and Poisson's Ratio? 29. E= 6/8 v =-ɛ(lateral)/E(axial)
Q2. A circular rod of 500 mm long is subjected to a tensile force of 50kN. The tensile strength is measured as 160 N/mm? and having the modulus of elasticity as 200KN/mm?. Calculate the Diameter of the steel rod (Express unit in mm) Elongation (i) (ii)
a bar is 500mm long and is stretched to 505 mm with a force of 50kn.the bar is 10mm diameter. calculate the stress and strain. the material has remained within the elastic limit. determine the modulus of elasticity
A cylindrical steel alloy rod with a 0.5 in. diameter is subjected to tension.Determine the magnitude of the load required to produce a 10-4 in. change in diameter if the deformation is entirely elastic. Assume a Young’s modulus of 30 * 106 psi and a Poisson’s ratio of 0.27.
A metal bar of variable cross section as shown and length is subjected to 1000 kN of force. The sections are of 1 m long section is 10000 sq.mm and that of 500 mm long section is 5000 sq.mm. Assuming the elastic modulus of 200 GPa, the total elongation of the bar will be?
SOLVE 5 DECIMAL
I need the answer quickly
Subject: STRENGTH OF MATERIALS (Civil Engineering) Round off to three decimal places