A bar made of steel has the dimensions shown in Fig. Q2. Two pairs of opposing axial forces of same magnitude are applied to the bar in x and y directions. Calculate the force in z direction SO that the total length in direction contracts 0.1 mm. The material behaves elastically. The young's modulus for steel is given as 10 GPa and v= l v=0.3. Z y Ez 80 KN 80 KN 100 mm 30 mm 60 mm

A bar made of steel has the dimensions shown in Fig. Q2. Two pairs of opposing axial forces of same magnitude are applied to the bar in x and y directions. Calculate the force in z direction SO that the total length in direction contracts 0.1 mm. The material behaves elastically. The young's modulus for steel is given as 10 GPa and v= l v=0.3. Z y Ez 80 KN 80 KN 100 mm 30 mm 60 mm

Name: A bar made of steel has the dimensions shown in Fig. Q2. Two pairs of
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A bar made of steel has the dimensions shown in Fig. Q2. Two pairs of opposing axial forcesof same magnitude are applied to the bar in x and y directions. Calculate the force in zdirectionsothat thetotallengthindirectioncontracts0.1 mm. The material

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2.6 The truss ABC shown in the figure supports a horizontal load P₁ = 9 kN and a vertical load P₂ = 18 kN. Both bars have cross-sectional area A = 1,290 mm² and are made of steel with E= 210 GPa. a) Determine the strain energy U₁ of the truss when the load P₁ acts alone (P₂ = 0). b) Determine the strain energy U₂ when the load P2 acts alone (P₁ = 0). c) Determine the strain energy U when both loads act simultaneously. 813 mm 1524 mm P₁ = 9 kN P₂ = 18 kN
Figure below shows the bar with three equal elements. Use the finite element method and calculate: 2.1 the global stiffness matrix 2.2 the displacement on node 2, 3, 4 2.3 the Strain in each element 2.4 the stresses in each element using Hook's law and compare with theoretical stresses (o=F/A) (1) (2) (3) -50 N 10 mm 10 mm 10 mm A1=50 mm? A2=20 mm? A:=10 mm? E=200 GPa
Determine the instantaneous stress and elongation of a 30 mm diameter bar if a mass of 60 kg falls through a height of 60 mm on to a collar which is rigidly attached to the bottom end of the bar as shown in Figure Q2. The bar is 1.2 m long and is suspended vertically. The Modulus of elasticity, E, for the material of bar is 210 GPa. Take g = 10 m/s2.
A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.24 mm the values of elastic modulus for steel is 221 MPa. Take H1 = 4 cm, H2 is 2 x 2 cm and bottom bar (Q) is 6 x 6 cm. Also, determine the stress-induced in each section of the bar. = 9 cm, top bar (R) IP Solution: R cm x RCm Steel bar i) Magnitude Force, P = H1 cm ii) Stress-induced in the top bar = Q cm x Q cm Steel bar H2 cm iii) Stress-induced in the bottom bar =
The stresses in a 2-D rectangular steel body (E = 200 GPa, v=0.32) are xx = -A(L - x)y, and oxy = A(h² - 4y²); other stress components are zero. Here, L represents length and h is height. What is the strain component y xy A - (h² - y²) 8E O A A 8G - (h²-x²) - (h²-x²) 8E А A= (h²-y:²) 8G ?
Let's consider a rod having a solid circular cross- section with diameter of 4 mm and it is made of a material having a Young's modulus E = 120 Gpa and a Poisson's ratio of 0.33. If a tensile force F is subjected to that rod cross-section, the diameter becomes 3.995 mm. determine the applied force F. Select one: F = 3427 N F = 2856 N F = 5712 N F = 8568 N F = 7140 N F = 2285 N
3. A 1.40 m long steel circular bar is acted upon by forces as shown in fig below. determine the total elongation of the bar. Take E steel=200Gpa and E brass = 85GN/m² 4 cm 3 cm 3 cm 40 kN 60 kN Steel 100 kN 80 kN Steel Brass 40 cm 60 cm 40 cm
Figure 2 shows a bar with a length L fixed at the left end. Question 2 The uniformly distributed force f (unit: N/m) is applied along the axis of the bar, and a concentrated force P (unit: N) is applied at the free end of the bar. The bar has a constant Young's modulus E and cross-section area A. Find the stretch of the bar: (a). at the free end of the bar; (b). at the center of the bar. (Expressing all the resulta with E, A, L, f, and P). E, A L Fig. 2. The kft end of the bar is fd, ad the froe ed of the bar is applied with a force P. The uniformly distribatod kece f is applied akong the ais of the bar.
The following stress condition is applied to a cubic material.Normal stress in the x direction is 15 Mpa, normal stress in the z direction is -7 Mpa and the shear stress in the x-z plane is 59 Mpa.(a) Write the stress tensor(b) Find the maximum normal stress(c) Find the angle with respect to the x- axis at which the maximum normal stress is applied(d) Find the maximum shear stress(e) Determine the angle with respect to the x-axis at which the maximum shear stress is experienced
A roadway sign that weighs Py = 14 kN is supported by a structural pipe with an outside diameter of 340 mm and a wall thickness of 10.5 mm. Wind pressure on the sign creates a resultant force of P₂ = 21 kN, acting as shown. Using length dimensions of a = 5.4 m and b = 6.3 m, determine (a) the normal and shear stresses at point H. (b) the normal and shear stresses at point K. P₂ Py b H y K