A bar ACB has is subjected to an external load at C, and it is supported either end by a cable as shown in fig. below. Calculate the smallest area of each cable if the stress is not to exceed 90 MPa in bronze and 120 MPa in steel.

Q: Please build this on solidworks (create your own dimensions) and then provide a single drawing.…

A: Note: In the given drawing, the type of unit is not mentioned. So, we will use MMGS (millimeter,…

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: Figure (1) shows a linkage that operates rock crushing mechanism. a= 9.32 in, b= 12.27 in, c= 3.0…

A: Below is the kinematic diagram for the rock crusherThere are 6 links which are numbered on that…

Q: Find the value of a. TO a. Vs +3

A:

Q: ab) What is the composite area's moment of inertia based on axis Yo?

A: we have to determine the MOI

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Given:Find:Draw the lines corresponding between the views.

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: Add the vectors using triangle rule or parallelogram rule

A: Draw the diagram of the vector system.

Q: Problem 3. a. A force has a magnitude of 1 kN and coordinate direction angles of 0,= 60°, 8, = 120°,…

A:

Q: One end of a piano wire is wrapped around a cylindrical tuning peg and the other end is fixed in…

A:

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that ,  Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: solve by showing every step.

A: Given data: The ultimate tensile strength of component is Sut = 30 ksi. The ultimate compression…

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: Given the isometric drawing of the solid, draw the multiview projection.

Q: complete 1-F on part a and b

A: Given Data: md2xdt2+cdxdt+kx=f(t)m=2 kgc=3 kg/sk=20 N/mf(t)=10 N   To Find: (a) Determine the…

Q: can you resolve and draw the fbd

A: Freebody diagram of the cut section:

Q: D 3.2-5. Use the graphical method to demonstrate that the fol- lowing model has no feasible…

A:

Q: Q2. (Answer One) AW-+号how tht +-0 ) "-/(). show that +-

A: Given To find prove the following

Q: Draw a perspective,isometric(with 30 angle), & oblique(with 45 amgle) view of a cube.

A: Draw a perspective,isometric(with 30° angle), & oblique(with 45° angle) view of a cube.

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: 1.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: Sure, based on the information provided in the text accompanying the image, the angle between lines…

Q: What is the answer in #3B. Show complete solution and FBD

A:

Q: JC BRA JC Ma = 2.5kg BRD BAD Mb=7kg Given that: The line of force for BRD is 5cm. Distance JC to Ma…

A: Mass, Ma= 2.5 kg Distance between JC and Ma, a= 16 cm Mass,Mb= 7 kg Distance between JC and Mb, b=…

Q: i need the answer quickly

A:

Q: both answers are wrong :(

A: Given DataT1=310KP1=320kPaM1=0.3 To findV2=?P2=?

Q: Statics Problem !!! Help me part D!!!! Answer it this Problem Correctly!! Please give correct…

A: I hope this is helpful

Q: Draft and annotate the 2D sketch of cover using AutoCAD and mention all the dimensions. Colour the…

A:

Q: 1- Sketch front, right and top views of the following object. Each grid represents 10 mm. Front

A: Given: Sketch Front, top and right side view of the given isometric view.

Q: Problem 2: Values: FA = 20 N FB = 30 N a = 25° Use the graphical method to determine... a) the…

A:

Q: Solve both and show all parts and solutions

A: The power to input shaft is The speed of gear of input shaft is The gear ratio is The loss in power…

Q: Find the oxthagonal r-6a.Cose whese a is pasametes

A: r=6acosθWhere a is a parameter Now need to calculate orthogonal trajectory

Q: olve show full solution

A: To find:The principle stress at point A and absolute maximum normal stress at and absolute maximum…

Q: Use a trammel to sketch the missing symmetric half of the figure. Do not dimension.

A: Given Sketch To find The symmetric half of sketch

Q: can the solve the last three quetsions please

A: mass of refrigerant R-22, m= 2kgThe initial pressure, P1= 6.8 barThe initial state is saturated…

Q: Draw Front and Side and top with all dimensions please

A: Draw the top view and side view first as shown in the below attached image:

Q: I tried the degree both 51 and 50.99 but it is incorrect. Plz help.

A:

Fluid Kinematics

The branch of science that deals with objects which are either in motion or stationary are studied under the branch of classical mechanics. Fluid mechanics is a subcategory of classical mechanics that deals with the behavior of fluids at rest (fluid statics) or in motion (posing some velocity). In fluid kinematics, studies focus on the associated motion of fluid particles or groups of particles, and its associated parameters like displacements, velocity, and acceleration without concerning about the forces that caused the motion. All the laws of classical mechanics are applied in the study of fluid kinematics.