A bar ABC is pinned at A and attached to a 12-mm diameter steel cable BD. a. If the allowable tensile stress in the steel cable is 140 MPa, what is the maximum safe value of the load Fapplied as shown in the diagram? b. What is then the shearing stress developed in the 20-mm diameter pin support at A? c. What is the bearing stress between the pin and the 25-mm thick support plates at A? 2 m 2.5 m B 75 mm- 3 m 25-mm thick 20-mm pin support diameter pin plates Detail of support A connection at A

Q: es Required information Problem 01.061- A two link assembly with point loads Two horizontal 13-kip…

A:

Q: A triangular beam, having a base of 30Ó mm, and a height of 500 mm. If fc' = 25 MPa, and the…

A:

Q: Q3 The cantilevered bar in the Fig 3 is made from a cast iron material and is statically loaded with…

A: Perhaps the main part of building a house is structural engineering and design. Structural…

Q: The vertical links (at BD and two at CE) has an thickness = 9.9 and width = 27.2 mm uniform…

A: bearing stress in BD member load at BD section will be remain 8.5N and diameter of the pin is 7.7 mm…

Q: res plate if the allowa and the plates is

A:

Q: Determine the a) normal stress in rod (1), b) the shear stress in pin B and the shear stress in pin…

A: To find out the normal stress in rod 1 and shear stress in pin A and B.

Q: The maximum shear stress (kPa) is most nearly 100 kPa 50 kPa -50kPa 50 kPa 75 O 56 O 66 O

A:

Q: The homogeneous 600-lb plate is suspended from three cables. Determine the tension in each

A:

Q: 10 mm 10 mm | | | |- | 50 mm 50 mm 10 mm الے 20 kN B 150 mm 910 mm 10 kN C 150 mm D Two vertical…

A:

Q: Problem 8.4 Distributed Loads The framing system shown in the figure is subjected to a 7.7 kN point…

A:

Q: D Front view 18 mm 6 mm B IB Side view 160 mm 120 mm Top view In the steel structure shown, a…

A:

Q: H.W. #4: A pin connected truss is loaded and supported as shown, determine: a) The normal stress in…

A: Determinea. The normal stress in member DE if it has cross sectional area of 750 mm2. b. The minimum…

Q: C 105° SIMPLE STRESSES 50° D 65° 1. Two steel bars are connected by two 20 mm 60 KN 15° BLOCK E…

A: At joint B Consider the summation of forces in the vertical direction TBC sin65o+TBD…

Q: The figure shows a roof truss and the detail of the connection at joint B. Members BC and BE are…

A: Given data: Shear stress τ = 70 MPa Bearing stress σ = 140 MPa Diameter of rivet d = 19 mm   For the…

Q: A joint connection is shown below. If the average shear stress in the pin must not exceed 107 MPa,…

A: Given: Max. shear stress = 107MPa, D=12mm = 12*10-3 Ma. applied load, P= ?

Q: 1. From the given truss below, answer the following: 9 m G 4 m 135 kN 135 kN B 4 m C4m E Compute the…

A:

Q: diameter of the smallest pin that can be used if not to exceed a shear stress of 60 MPa (Draw

A:

Q: Figure P-130 shows a roof truss and the detail of the riveted connection at joint B. Using allowable…

A:

Q: A T-beam with the cross-section shown above is subject to the loads shown. a) Determine the second…

A: Given:- To find:- Second moment of area SFD and BMD Normal stresses at A, B and C Concept:-…

Q: What is the Maximum Shear Stress, t, on the centric axially loaded member shown? The cross-sectional…

A: Given data : Axial load (P)=40 kipsCross sectional area (A)=2 in2

Q: D 30 kN 70 kN 2 m 12 mm-thick gusset plate 10 -mm-thick 2 m angle 1.5 m-15 m- 15 m--15 m 8 mm-thick…

A:

Q: Knowing that a force P of magnitude 1000 N is applied to the pedal shown, determine (a) the diameter…

A:

Q: The

A:

Q: With

A:

Q: Question 3 A compressive force of 45 kN acts parallel to the longitudinal axis of the I-section as…

A:

Q: A roof truss and the detail of the connection at joint B are shown in the figure. Angle sections…

A: For the given roof truss:

Q: 2,300 mm A 1,150 mm 1,600 mm 75 kN

A:

Q: Consider the truss structure and the loading given below. a) Compute the average axial stress on…

A: Take equillibrium at point B to find force

Q: A 300 mm M 30 mm 30 mm B. 150 mm 150 mm a) Determine the bending stress developed at point A. b)…

A:

Q: Knowing that a force P of magnitude 750 N is applied to the pedal shown, determine (a)the diameter…

A: Given: The magnitude of force, P = 750 N The average stress in pin, σavg=40 MPa Pedal thickness, tp…

Q: BOLTED/RIVETED CONNECTION: SITUATION: In the figure, assume that a 20-mm-diameter rivet joins the…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…