7. A balanced three-phase source serves three loads as follows:Load 1: 24 kW at 0.6 lagging power factorLoad 2: 10 kW at unity power factorLoad 3: 12 kVA at 0.8 leading power factorIf the line voltage at the loads is 208 V at 60 Hz, calculate the complex power, the magnitudeof the line current and the combined power factor of the loads.

Answered: Image /qna-images/answer/1d2191d8-77e3-4048-bbc5-2ec826d71f1a.jpg

Answered: A balanced three-phase source serves…

A balanced three-phase source serves three loads as follows: Load 1: 24 kW at 0.6 lagging power factor Load 2: 10 kW at unity power factor Load 3: 12 kVA at 0.8 leading power factor

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.19P: Consider a single-phase load with an applied voltage v(t)=150cos(t+10)volts and load current...

See similar textbooks

Similar questions

A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase 60-Hz,208-V source, (a) Calculate the line current, the total real and reactive power absorbed by the load, the load power factor, and the apparent load power, (b) Sketch a phasor diagram showing the line currents, the line-to-line source voltages, and the -load currents. Use Vab as the reference.
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. Use Gauss-Seidel method in Matlab to analyze the system the tolerance of error is 10-3. Then anwser the questions as follows. V, = 1.05200 0.01+ j0.025 300 + j200 MVA 0.015 + j0.035 150 MW 200 +j150 MVA 0.01+ j0.03 |V = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03 2.
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. ' qu V = 1.05200 0.01+ j0.025 300 + j200 MVA 3 0.015 + j0.035 150 MW 200 + j150 MVA 0.01 + j0.03 |V = 1.03 The admittance matrix (Y_bus)? The bus power in per-unit?
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
please give me the answers for all this questions
The one-line diagram of a three-phase power system is shown in the above figure. The line impedances are in per- unit on a 100-MVA base, and the line admittances are neglected. ' V, = 1.05200 0.01 + jo.025 300 +j200 MVA 3 0.015+j0.035 150 MW 200 +j150 MVA 4 0.01 + j0.03 |V2 = 1.03 The admittance matrix (Y_bus)? 0.02 + jo.04 0.0125 + jo.03
Two balanced loads are connected to the a 240kVrms60Hz line as shown in the figure below. Load 1 draws30kW at a power factor of 0.6 lagging and load 2 draws 45 kVAR at power factor of 0.8 lagging. The real power, reactive power, and magnitude of the line current absorbed by the combined load is close to kW, kVAR, and A. Two balanced loads are connected to the a 240kVrms 60Hz line as shown in the figure below. Load 1 draws 30kW at a power factor of 0.6 lagging kW. and load 2 draws 45KVAR at power factor of 0.8 lagging. The real power absorbed by the combined load is close to Balanced load 1 Balanced load 2
The three phase power and line-line ratings of the below electric power system is given below: V. Vm G G: 50 MVA 22 KV X= 4% T: 50 MVA 22/40 KV X= 4% M: 43.2 MVA 36 KV X= 4% By choosing 100 MVA and 22 KV on the generator side as base values, the new per unit impedance of the generator is and the new perunit impedance of the motor is None of these 8.333% Impedan 11.43% 7.5% 10.238% erunit on a100MVA. 100 KV base. The load at bus 2 s S2= 16MW - 32 MVAR, and the load at bus 3 is 5OMVA at 0.8 pf lagging. It is required to hold the voltage a
This question in (three phase) subject.. I want the the correct answer from choices ..
A balanced Y-connected generator with terminal voltage Vbc 5 200/08 volts is connected to a balanced-D load whose impedance is 10/408 ohms per phase. The line impedance between the source and load is 0.5/808 ohm for each phase. The generator neutral is grounded through an impedance of j5 ohms. The generator sequence impedances are given by Zg0 5 j7, Zg1 5 j15, and Zg2 5 j10 ohms. Draw the sequence networks for this system and determine the sequence components of the line currents.
power factor is The three phase power and line-line ratings of the below electric power system is given below: T. Vm M G: 50 MVA 20 KV X= 4% T: 50 MVA 20/40 KV X= 4% M: 43.2 MVA 36 KV X= 4% By choosing 100 MVA and 20 KV on the generator side as base values, the new per unit impedance of the generator is and the new perunit impedance of the motor is 16 % None of these 8% VA at 0.8 pf leading at line to line voltage of 18 KV. 4% bedance of this load on a base of 100MVA and 20 KV. Select one: O a. 5.183-j3.888 pu Ob. 5.183 + j 3.888 pu Oc.1.295-10.972 pu EN O 1:49
Draw Wye- Delta three phase transformers connection ( no-load and full-load) in Lt-spice