A balanced three-phase circuit has the following characteristics: i. Y-Y connected i. The line voltage at the source, Vab is 415.69 angle 90 deg. ii. The phase sequence is negative iv. The line impedance is 4+j5ohms/phase; V. The load impedance is 76+j55ohms/phase. Determine: a) The line current of each phase. b) The line voltage of the load terminal.

A balanced three-phase circuit has the following characteristics: i. Y-Y connected i. The line voltage at the source, Vab is 415.69 angle 90 deg. ii. The phase sequence is negative iv. The line impedance is 4+j5ohms/phase; V. The load impedance is 76+j55ohms/phase. Determine: a) The line current of each phase. b) The line voltage of the load terminal.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The Figure shows a balanced Y-A 3Ø circuit. The phase voltages of the Y-connected source are V, = 11020°, V, = 1102 - 120° and V. = 1102120°, Volts. The line impdedances are Z,=10+j5 Q each. The impedances of the A-connected load are ZA = 75+j255 N each. Determine: Line Currents, Phase Currents (load), Power drawn by the load. Ve ZA Vb
A load of 138+j460 Ohm is supplied through 3+j14 Ohm line as shown in Figure 1. (a) Find the average power dissipated in the line. (b) Find the value of capacitive reactance connected across the load to compensate the reactive power need of the load. (c) What is the equivalent impedance after compensation. (d) Find the average power dissipated in the line when the capacitive reactance is connected across the load. (e) Express the power loss in (d) as a percentage of the power found in (a) j14 Figure 1 7200/0 + V (rms) Source 3 wi Line Load 138 j460
This question in (three phase) subject.. I want the the correct answer from choices ..
Answer number 6 please
An 11kV, three phase transmission line has a resistance of 2 ohm and reactance of 4 ohm per phase. The efficiency of the line when supplying a load of 4MW at 0.8 lagging power factor is nearly .. Select one: O a. 97.8 % O b. 90.6 % OC.95.4 % O d.99.2 %
Solve part c.
28 k
Q2
Convert followin BCD number into the EX-3 code 1011 1001
Phase Qz/ The eas Voltages at the terminal of abalan ced Y connected load is VAN=12o 28. Each Phase of the load consist of lo 230° .Find the active & Reactive and Complex Power Per-Phase then find the total Powers For three Phase load.
A single phase, unity power factor load takes 90 Amps at 10 kV. Using a base voltage of 65 kV and base kilovolt amperes of 4475 kVA. Find the base current, base impedance, base power, per unit current and per unit voltage of the load.
2. A single-phase a.c. distributor AB is fed from end A and has a total impedance of (0-2 + j 03) ohm. At the far end, the voltage V = 240 V and the current is 100 A at a p.f. of 0-8 lagging. At the mid-point M, a current of 100 A is tapped at a p.f. of 0-6 lagging with reference to the voltage Vy at the mid-point. Calculate the supply voltage V, and phase angle between V, and Vg- [292 V, 2-6°] a loade