(a) A transfer function represents the relationship between the output signal and the input signal of a control system. Two different transfer function models of a temperature control system have been proposed by the process engineer at XYZ Company, namely Model A and Model B: 17 Model A = s+6s+34 15 Model B = 2s +16s+ 30 (i) Plot the poles location for Model A and Model B on s-plane. (ii) Sketch the unit step responses of Model A and Model B in the same axes. (iii) Based on results from part (ii), which is the best system to be used? Give your reason.

(a) A transfer function represents the relationship between the output signal and the input signal of a control system. Two different transfer function models of a temperature control system have been proposed by the process engineer at XYZ Company, namely Model A and Model B: 17 Model A = s+6s+34 15 Model B = 2s +16s+ 30 (i) Plot the poles location for Model A and Model B on s-plane. (ii) Sketch the unit step responses of Model A and Model B in the same axes. (iii) Based on results from part (ii), which is the best system to be used? Give your reason.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the 8X1 Muitiplexer shown in the figure below. if the selectors A=0 and B=1, the value of the multioplexer output will be D. D. D. 0 D. &1 MULTIPLEXER D. D. 1 D S, S. A F=C' F=C F=1 F=0 If the following data-input waveforms applied to the comparator, the * outout in O O O O
Powered by ±10VIntegrator circuit designed with Op-AmpVin=3sin(2π400t) alternative signal to inputhas been applied. Analysis of output voltage (Vo)Draw the waveform.Calculate the maximum and rms value of out signal.
Q- 2: Suppose you are designing a Mathematical Calculator. You need Logarithmic and Anti logarithmic functions for the calculator. Draw a neat circuit diagram of an Op Amp based log Amplifier. Derive the output voltage expression for the above circuit justifying its name. Draw a neat circuit diagram of an Op Amp based Anti-Log Amplifier.
Input signals are given as V1= 3sin(wt), V2= 2sin(wt) and V3= 1sin(wt) in circuit.) a) Find equation that expresses output signal in terms of input signals. b) Write sinuzoidal expression of output signal.
Discuss the effect of increasing and decreasing proportional gain to the system output. Discuss the effect of increasing and decreasing derivative gain to the system output. Discuss the effect of increasing and decreasing the integral gain to the system output. 4. Discuss some advantages of using Simulink over the MATLAB codes I WANT THE ANSWER FOR THIS QUESTION WITHOUT PLAGIARISM
3 A. We have a 4-bit DAC with Vref = 3.3V and an input voltage of Vs = 2.05V. Draw a diagram illustrating the conversion process of a successive approximation ADC. Label the x-axis conversion step and the y-axis Digital Number(DN). What digital number (DN) will be returned by the DAC within the SAR ADC? 3 B. You have purchased an 8-bit R-2R digital to analog converter to control the joint position on a robot arm (which is proportional to the input voltage). a). The DAC shows an output voltage of 0.49 V when the binary value 00011001 is applied. What is the full-scale analog output range of this DAC in volts? b). What voltage does the DAC output with a binary value of 10101010 applied? c). If the joint rotates 10.0 degrees/V applied, what is the minimum joint rotation increment you can achieve with this DAC?
4. ( Determine the output C using signal flow graph. Show step-by-step solution and equivalent signal flow graph in each step. Show step by step and complete solution. R G₁ H₁ G₂ H₂
In Figure is given .. 10 - Ys) Ys) R() G{s) O A) there are not correct ans swers O B) multiple input and single output system (MISO) C) single input and multiple output system (SIMO) O D) single input and single output system (SISO) E) multiple input and multiple output system (MIMO)
shows a block diagram of a process con- trol system. Determine the range of the gain K for stability. Figure K Figure Process control system. Verify using Nyquist on Matlab
please show the step claerly
a) Design a 4 i/p multiplexer (4-to-1).
Digital e