The signal is the sum of x1(t) and x2(t) such that x1(t)=cos[2Ont] and x2(t)=cos[100At]. The sampling frequency is 40 Hz. With this, f2(t) an alias of f1(t) at Fs. True False

Q: Q OUT CLK

A: STATE TABLE OF D-FLIP FLOP: D(Input) Qn+1(Next sate) 0 0 1 1   CHARACTERISTICS TABLE OF…

Q: What is the main distinction between an active device and a passive device?

A: The main difference between active and passive device is as fallows:

Q: Comparison of types of analogue to digital conversion؟

A: Types of ADC Dual slope ADC Flash ADC Sigma delta ADC Successive Aprroximation ADC

Q: Modulator is a term used to describe any device that converts signals.explain

A: For the wireless transmission of the signal, the signal message signal must be amplified and must be…

Q: What can be concluded from the computed average percent error (0%) with reference to the 5%…

A: It is given that, The computed average percent error is 0% and  The tolerance of the resistors is…

Q: Briefly explain Analog to Analog conversion techniques with the help of diagrams?

A:

Q: QUESTION 5 Determine the gate output for the input waveforms in Figure3 and draw the timing diagram.…

A: Given waveform with the logic circuit,

Q: Subject:electronic engineering How BJT acts as a switch?

A: One of the major applications of the Bipolar Junction transistors is the switch. The transistor act…

Q: An FET biasing technique that can be solved directly using either mathematical or graphical…

A:

Q: Create a list of three distinct analog-to-digital conversion technologies. What were the reasons for…

A: Analog-to-digital conversion (ADC) is  process in which an or analog, signal is changed into a…

Q: What will happen if you increase VDD after constant current area region?

A: CONSTANT CURRENT SOURCE  Constant current source is a power device source which provides a constant…

Q: what is the difference between a sequential circuit and a combinational circuit in Digital Circuit…

A: Need to brief about the sequential and combinational circuit in digital circuit.

Q: An analog-to-digital converter outputs an analog voltage. True or false?

A: Given Analog to digital converter(ADC)

Q: What is CMC and DMC in electrical circuit?

A: Both common mode choke and differential mode choke are types of inductors that are used in…

Q: 5. In the circuit shown below, if Ro is given, what value must R₁ have in order than the input…

A: The circuit diagram,The input resistance between the terminal is ,

Q: Is the PEC a law? What is a small appliance branch circuit?

A: Small appliance branch circuit: This circuit is used for mainly in the kitchen area and not used for…

Q: Question) Why to Digital and viee conversion im below mentioned process? need Amala we Nersa we…

A: Any physical signal,such as sound,or a light,or a voltage is considered an analog signal. The thing…

Q: For the given sequential circuit; a)What is the realization topology, b)Write down corresponding…

A: Given:A circuit, To find:a) Realization topology,b) State equation,c) State transition table,d)…

Q: Explain the steps for chip mounting.

A: Chip mounters are required for the mass manufacture of consumer and other electronic products…

Q: Please provide a minimum of three techniques for analog-to-digital conversion. What factors led to a…

A: To do:We have to provide a minimum of three techniques for analog-to-digital conversion. Also we…

Q: Compute for the Rmax in an 8 bit R/2nR DAC with Rmin of 100 Ohm. 1.28k Ohm 25.6k Ohm 1.27k Ohm 25k…

A: To find the Rmax in an 8-bit R/2nR DAC  Given : Rmin = 100 ohm

Q: with neat diagram explain the construction and working princple of Electronics Amplifiers.

A: Electronics Amplifiers: The device that increases the power of the signal is called an electronic…

Q: What is biomedical Instrumentation explain with examples

A: Biomedical Instruments  Bio-Medical Instruments is the application of knowledge and technology to…

Q: Requirements: 1. Explain what is an ADC converter and how the conversion process happens? 2. Show…

A: The detailed answer is solved below according to the given parameters and instructions in the…

Q: identify which one is not a signal conditioner? a. P-I convertor

A:

Q: Determine (Vo1). (Vez) and (Vas) for the circuit shown below. Vol Vet 200 k 100 An 200 An Vas s00 AD…

A:

Q: What are the function of the following 8085 pins: INTR, RESET, HOLD, TRAP, ALE.

A: Function of INTR : INTR is a pin in 8085 microproccesor when this pin goes high its completed the…

Q: Explain the different classifications of Analogue to Digital (A/D) converters and compare their…

A: We have to explain the different classifications of Analogue to Digital (A/D) converters and compare…

Q: ISCUSSION: Give to applications for the multiplexer.

A: There are following multiplexer application are: 1.  We can take output as per according…

Digital to Analog Converters

Digital to analog converters are commonly known as DAC, digital analog converter, D2A, or Digital-to-Analog converters. DACs are one of the important devices used in the electronics and electrical domain. DACs are the systems that convert a digital signal into an analog signal, whereas an analog to digital converter or ADC performs the opposite function. Digital signals are those signals that can represent the information or data as a set of discrete values. At a particular instant of time, a digital signal can only take a particular value of data. A digital signal is characterized by two unique values; zeros and ones, or true and false, represented by the Boolean domain. These are also known as binary signals or logic signals. Unlike digital signals, an analog signal is represented by continuous values, where at any time instant, the analog signal is represented by a real number.