Compute for the Rmax in an 8 bit R/2nR DAC with Rmin of 100 Ohm. 1.28k Ohm 25.6k Ohm 1.27k Ohm 25k Ohm

Q: Digital instruments are better than Analog instruments justify this with any four features

A: The features of the digital system are discussed below:

Q: Question 12 Active electronics devices Select one: o a. O b. O C. O d. O e. requires electrical…

A: In these questions, we need to choose the correct options. Here, we are discussing about the active…

Q: Q1. By using a neatly diagram if necessary, explain each specification of a typical monolithic A/D…

A: Given By using a neatly diagram if necessary, explain each specification of a typical monolithic A/D…

Q: Choose the correct statement from the following statements refered to a PV Module, for the…

A: Given, Number of lamps connected across the PV module is increased.  Explanation :-  As the lamps…

Q: Write an assembly code in 8051 microcontroller where the input is the temperature sensor, goes…

A: We have to write an assembly code in 8051 microcontroller where the input is the temperature sensor,…

Q: Q9. The full subtractor circuit is implemented using D. one OR gate B. two AND gates A. two XOR…

A: here we have to identify by using which gates gates we can implement the FULL SUBTRACTOR.....

Q: Modulator is a term used to describe any device that converts signals.explain

A: For the wireless transmission of the signal, the signal message signal must be amplified and must be…

Q: Briefly explain Analog to Analog conversion techniques with the help of diagrams?

A:

Q: Make a list of three technologies that have gone from analogue to digital. What was the reasoning…

A: Analog devices works on a continuous type signals while digital signal works on discreate type of…

Q: Question 3: Write the state transition table and draw the state machine figure of the sequential…

A:

Q: An FET biasing technique that can be solved directly using either mathematical or graphical…

A:

Q: Create a list of three distinct analog-to-digital conversion technologies. What were the reasons for…

A: Analog-to-digital conversion (ADC) is  process in which an or analog, signal is changed into a…

Q: How does R-2R DAC is better than Binary-weighted Resistor DAC?

A: Given that  How does R-2R DAC is better than Binary-weighted Resistor DAC?

Q: An analog-to-digital converter outputs an analog voltage. True or false?

A: Given Analog to digital converter(ADC)

Q: 5. In the circuit shown below, if Ro is given, what value must R₁ have in order than the input…

A: The circuit diagram,The input resistance between the terminal is ,

Q: Q. The input for any circuit at lab experiments are O B. the switches OD. None of the above O C.…

A: While performing the experiments in Laboratory, the inputs is given at one terminal and switches and…

Q: An analogue indicating instrument with a scale range of 0-5A shows a current of 2.4A. A current has…

A:

Q: Which of the following statements about resistive transducer instrumentation is true? Strain gauges…

A: A resistive transducer instrument is used to measure the load, pressure or displacement.

Q: Can I get help drawing the circuit for 3 pleease like the 2nd one

A:

Q: Draw the equivalent circuit for summing amplifier and voltage amplifier.

A: The voltage amplifier is a device that is used to amplify the input voltage signal. An op-amp is…

Q: (a) Consider the characteristics of the three Resistance Temperature Detectors (RTD) types shown…

A:

Q: What is the device address used by the instruction OUT A4, AL?

A:

Q: 1.Draw an example Turn-on Snubber circuit and explain its working principle and what it is used for.…

A: (1) It is asked to draw a turn-on snubber circuit and also asked to explain its working principle.…

Q: What are the function of the following 8085 pins: INTR, RESET, HOLD, TRAP, ALE.

A: Function of INTR : INTR is a pin in 8085 microproccesor when this pin goes high its completed the…

Q: Implementation of 1, 2 and 4 quadrant switches. Explain the concept of 1, 2 and 4 quadrant switches…

A: In various applications in power electronics, different  types of switches are required. Here, we…

Q: q3 Choose correct answe

A: Although range of input values at which output value gets saturated  is known as the dead space of…

Q: Solver 200/5A Is=2.75A Ip=?

A: Given data CT Ratio; 200/5A Secondary current; Is=2.75 A To find out We have to determine the…

Q: What are the different types of analog to digital converter? (Hint: There at least three types of…

A:

Q: IV- Define with draw the block diagram the sensor fusion.

A: Sensor fusion aims to overcome the limitations of individual sensors by gathering and fusing data…

Q: can you give an Introduction about 3 Band Equalizer, the use of it and how it works

A: We have given the problem  can you give an Introduction about 3 Band Equalizer, the use of it and…

Q: V. S/H Counter Out Reset Integrator Clk a. Why does the circuit shown called that name? b. What are…

A: The ADC is an analog to digital convertor. The machines understand the digital binary bits in their…

Q: With a neat diagram ,explain about the working of 4 bit R-2R ladder Type DAC.

A: Working of 4-bit R-2R ladder type DAC DAC stands for Digital to analog converter

Digital to Analog Converters

Digital to analog converters are commonly known as DAC, digital analog converter, D2A, or Digital-to-Analog converters. DACs are one of the important devices used in the electronics and electrical domain. DACs are the systems that convert a digital signal into an analog signal, whereas an analog to digital converter or ADC performs the opposite function. Digital signals are those signals that can represent the information or data as a set of discrete values. At a particular instant of time, a digital signal can only take a particular value of data. A digital signal is characterized by two unique values; zeros and ones, or true and false, represented by the Boolean domain. These are also known as binary signals or logic signals. Unlike digital signals, an analog signal is represented by continuous values, where at any time instant, the analog signal is represented by a real number.