a) A locomotive is travelling at 35 m/s up an incline of 0.006 radians when the engine cuts out. How far will the locomotive travel up the incline before coming to rest? Assume there are no frictional losses, no energy input from the engine, and take acceleration due to gravity to be 9.81 m/s². Give your answer in km. b) Round your answer to 4 significant figures. What is the speed (in m/s) of the locomotive after it has travelled a distance 5.83 km? Round your answer to 3 significant figures.

a) A locomotive is travelling at 35 m/s up an incline of 0.006 radians when the engine cuts out. How far will the locomotive travel up the incline before coming to rest? Assume there are no frictional losses, no energy input from the engine, and take acceleration due to gravity to be 9.81 m/s². Give your answer in km. b) Round your answer to 4 significant figures. What is the speed (in m/s) of the locomotive after it has travelled a distance 5.83 km? Round your answer to 3 significant figures.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Read the questions carefully before answering. Show complete solution with proper derivatives/integrals and units.Box or indicate your final answers when solving. Use 2 decimal places for final answers.
q9 A car left skidded along a road for 160 m. Assuming that the car skidded to a stop with a constant acceleration of -6 m/s^2, determine the speed of the car in km/h (to one decimal place) before it began to skid.
An engineer is designing the runway for an airport. Of the planes that will use the airport, the lowest acceleration rate is likely to be 2.98 m/s2. The takeoff speed for this plane will be 65.69 m/s. Assuming this minimum acceleration, what is the minimum allowed length (m) for the runway? Round off only on the final answer expressed in 3 decimal places.
The MDF sheet shown in the figure below iscut by a laser pointer, which moves through the curved groove. Your distance in meters measured along the slot is given by s = 9t2– 2t, with t in seconds. The laser is at A at time t = 0.2 s and at B when t = 3.0 s. Determine to two decimal places of precision:a) the magnitude of the average acceleration between A and B;b) the average vector acceleration between A and B.
2. A car starts from rest and travels 8 sec with an acceleration of a = 4-0.3t, then runs for 33 sec at constant velocity and finally comes to rest by decelerating at 3.125 m/s². a) Determine the velocity of the car after 10 sec. b) Determine the distance traveled by the car during the period of 10 sec. c) Determine the total distance traveled by the car until it stops. Kindly draw the fbd drawing. Thank you.
3. How to solve E, G, and H?
An object rotates about a fixed axis, and the angular position of a reference line on the object is given by 60=1.7e.43t where e is in radians and t is in seconds. Consider a point on the object that is 1.3 m from the axis of rotation. At t=1.3s, find the magnitude of the point's tangential component of acceleration? Round your answer to one decimal place.
1- Please I want answer for this question by typing it. Thanks
The end of the cable at B is pulled down with a constant speed. A 3 B V1 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value m S V1 3 Using absolute dependent motion analysis of 2 particles, a. Determine the speed of the anvil, VA. b. Is the anvil going up or down? VA= Round your final answers to 3 significant digits/figures. m Is the anvil going up or down? O up O down
A 50cm radius plate rotates at 18.85 rad/s. If the dish mass is 10kg, calculate A) the magnitude of the tangential velocity B) the frequency of motion C) the period D) the centripetal acceleration E) the magnitude of the force Express your response with a single significant number in decimals and with units
DYNAMICS OR RIGID BODIES (PLEASE WRITE THE COMPLETE SOLUTION. PLEASE WRITE & DRAW THE COMPLETE SOLUTIONS WITH FBD LEGIBLY. NO LONG EXPLANATION NEEDED. ANSWER IN 2 DECIMAL PLACES. BOX THE FINAL ANSWER.USE 9.81m/s2 or 32.2 ft/s2 for accelaration if necessary.) Determine the time and displacement of the ball at the same height from the ground.
Read the problems carefully and provide complete solutions with derivation of formulas(integrals and derivatives). Use two decimal places for final answers only. Final answers shown below are incomplete.