For each pulley system given below, calculate the acceleration of mass A in m/s2 (positive upwards) and then caldulate Z 10 a, +5 a2 where a, and az are the accelerations of mass A in system 1 and 2 respectively, Take mA-55.8 kg, mg 7.9 kg, and g 9.81 m/s. Assume lightweight and frictionless pulleys. Round your final answer for Z to two decimal places. System 1 System 2 B mB g A

For each pulley system given below, calculate the acceleration of mass A in m/s2 (positive upwards) and then caldulate Z 10 a, +5 a2 where a, and az are the accelerations of mass A in system 1 and 2 respectively, Take mA-55.8 kg, mg 7.9 kg, and g 9.81 m/s. Assume lightweight and frictionless pulleys. Round your final answer for Z to two decimal places. System 1 System 2 B mB g A

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.19P: Plot the earths gravitational acceleration g(m/s2) against the height h (km) above the surface of...

See similar textbooks

Similar questions

1) From 0 to 10 sec, find alphaA1, alphaC1 in rad/s^2, omegaA1(t), omegaC1(t) in rad/s, thetaA1(t), thetaB1(t) and thetaC1(t) in rad, and the distance made by the load s1 in inches and in feet made by the load during this time.
Q1. The image below shows an example of "absolute dependent motion analysis", where the motions of two objects depend on each other, and the goal is to find the relations in their motions (i.e., in their positions, velocities, and accelerations). Please put the suggested steps of analysis in the correct order. VA A B VB Differentiate the entire equation with respect to time, and extract the relation in velocities. Repeat for acceleration if needed. Set up a coordinate (s) along the direction of motion from a fixed point (O) or a fixed datum line. Represent the positions of the objects respectively. In some cases intermediate objects need to be considered too and their positions need to be represented as well. Recognize the constant length(s) and find the depending geometric relations between the position variables.
An object rotates about a fixed axis, and the angular position of a reference line on the object is given by 0=let, where 0 is in radians and t is in seconds. Consider a point on the object that is 1.46 m from the axis of rotation. At t=1.7s, find the magnitude of the point's radial component of acceleration? Round your answer to zero decimal places.
A shaft rotates with uniform angular velocity 10 rad/s for 10 seconds. The shaft continues to accelerate at 0.5 rad/s² for the next 10 seconds. Thereafter the shaft rotates with a uniform angular velocity. Find the total time to complete 1000 radians.
A cart weighing 0.5 kg is drawn up a smooth 45° incline by a motor, M, winding up a cable. The force in the cable can be expressed as 5t² N, where t is in seconds. When t = 0, the displacement s = 0 and the initial velocity is 3 m/s. Find the cart's velocity when t = 2 seconds. > Draw a very clear FBD of the cart that you can use to write the equations of motion > Write the equations governing the cart's motion along the incline. Use axes parallel and perpendicular to the incline. Find the velocity requested
Consider the portion of an excavator shown. At the instant under consideration, the hydraulic cylinder is extending at a rate of 6 in./sec, which is decreasing at the rate of 3 in./secevery second. Simultaneously, the cylinder is rotating about a horizontal axis through O at a constant rate of 12 deg/sec. Determine the velocity v and acceleration a of the clevis attachment at B. 2.7 B 3.6' PA 37° Part 1 Correct Determine the indicated terms used in the velocity and acceleration formulas. 2.7 B 3.6' 37° Answers: r- 75.6 in. 37 トー 6 in./sec 9 - 0.21 rad/s Fー -3 in./sec? 0 - rad/s?
Consider the portion of an excavator shown. At the instant under consideration, the hydraulic cylinder is extending at a rate of 6 in./sec, which is decreasing at the rate of 3 in./secevery second. Simultaneously, the cylinder is rotating about a horizontal axis through O at a constant rate of 12 deg/sec. Determine the velocity vand acceleration a of the clevis attachment at B. B 2.7 3.6' 370 Part 1 Correct Determine the indicated terms used in the velocity and acceleration formulas. B 2.7' 3.6' 37° Answers: r- 75.6 in. 37 in./sec 9 - 0.21 rad/s -3 in/sec? 0 - rad/s?
In a rope-climbing competition, all of the lifting is done by the arms; legs can only dangle. Imagine 220-lb Garvin Smith in training, hanging stationary from the rope, his legs off the floor. When prompted by his coach, he rapidly lifts his center of mass by 4 ft. in 0.65 s. Calculate Garvin Smith's acceleration. Round the final answer to one decimal place. Determine the net force (“force imbalance”) producing the acceleration. Round the final answer to one decimal place. Which forces are acting on Smith? (Note that his arms are part of himself, so they cannot exert a force on Smith.) With what magnitude force is Smith pulling down on the rope? Round the final answer to one decimal place. The force of 130.2 lb points _____.
An L-shaped bar ABC has known velocity v and acceleration a, at point A and known ang ular velocity WABC and angular acceleration a ABC- The dimensions and parameters you are to use are provided in the table below. Signs denote + for CCW,- for CW, + for right, and- for left. B Determine the acceleration vector in terms of unit vectors for point C at this instant using vector math. LAB LBC Units in in A-F 7.5 5.0 LBC LAB LAG Ө WABC ABC deg rad/s rad/s 33 3.5 21 VA in/s 13.0 WABC ABC aA in/s² 24.0 a VA
1- Find the velocity i and the position x as functions of the time t for a particle of mass m, which starts from rest at x =0 and t =0, subject to the following force functions: (a) F, = F.+ ct (b) Fx = F, sin ct (c) Fx = F, ed Where F, andc are positive constants.
1- Find the velocity x and the position x as functions of the time t for a particle of mass m, which starts from rest at x =0 and t=0, subject to the following force functions: (a) F, = F. + ct (b) F = F, sin ct (c) F, = F, ed Where F, and c are positive constants.
In a pulley system shown, find the tension on the cable and the acceleration of pulley B and the load 5kg. Acceleration of load (al-m/s²) = TENSION (N) = Acceleration of pulley (ag-m/s²) r