A 6 m simply supported beam shown in Figure la has a uniformly distributed load of 10 kN/m (plus quarter of the last two digits of your ID No., kN/m) and a uniformly increasing load of 15 kN/m (plus half of the last two digits of your ID No., kN/m). If Figure lb is the section materials used in the simply supported beam, determine the maximum flexural compressive and tensile stresses (kPa) in the beam section due to the applied loads? 500 200 300 2.5 m 3.0 m (а) (b) Figure 1. Simply supported beam with: (a) applied loads, and (b) beam section in mm units

A 6 m simply supported beam shown in Figure la has a uniformly distributed load of 10 kN/m (plus quarter of the last two digits of your ID No., kN/m) and a uniformly increasing load of 15 kN/m (plus half of the last two digits of your ID No., kN/m). If Figure lb is the section materials used in the simply supported beam, determine the maximum flexural compressive and tensile stresses (kPa) in the beam section due to the applied loads? 500 200 300 2.5 m 3.0 m (а) (b) Figure 1. Simply supported beam with: (a) applied loads, and (b) beam section in mm units

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q8 نقطة واحدة The Bouguer anomaly over an isostatically compensated region is Zero Positive Negative Same as isostatic anomaly صفحة 9 من 12 التالي رجوع عدم إرسال كلمات المرور عبر نماذج Go ogle مطلقا. SelealjeL.University Of Misan Jalsl lio eLai ai II
I want an accurate and detailed solution
Problem Number 2 Using the slope-deflection method, draw the bending moment diagram. 3m B 2EJ 4m * 20kN/m 3m 5. Moment @ D -11.09kN-m -40.82kN-m -34.43kN-m O -24.34kN-m EJ ЗЕЈ D
Problem Number 2 Using the slope-deflection method, draw the bending moment diagram. 3m B 2EJ 4m * 20kN/m 3m 4. Moment @ A O 49.51kN-m -32.99kN-m O -12.55kN-m O -55.05kN-m EJ 3E] D
USE THE SLOPE DEFLECTION METHOD TO ANALYSE THE BEAM BELOW AND ALSO DRAW SFD AND BMD AND NET BENDING MOMENT DIAGRAM
↓↓ 3m 185 f 285 t 3m 3.5m compute a) Fixed-end moment b.) Distribution factors c) Moment at B fin 1.5 moment distribution t
b. Situation 15: ockwise) 3,132/EI rad (clockwise) A non-prismatic beam is loaded as shown in the figure. The value of Pis 120 kN. a. b. AE 1 1.50 m 1. b. B 21 1.50 m P 303.75/El m (downward) 291.38/El m (downward) C Which of the following most nearly gives the value of the constant term in the deflection equation for segment BD? -371.25 33.75 21 1.50 m 291.38/EI m (downward) 219.38/El m (downward) b. d. Which of the following most nearly gives the deflection at B? D 1.50 m d. 371.25 33.75 d. Which of the following most nearly gives the deflection at C? 219.38/El m (downward) 330.75/El m (downward) 303.75/El m (downward) 330.75/El m (downward)
i need it ASAP please thank you
Answer the following problems using Moment Area Method
1.FIND FOR LOCATION REACTIONS AND THEIR DIRECTIONS
2. Refer to the given frame below. Using Portal Method in the analysis of frames, determine the following: Column shears at GL, HM, and IN (KN) b. Column moments at GL, HM, and IN (KN.m) c. Column moments at LQ, MR, and NS (KN.m) d. Girder moments at FG, GH, MN, and NO (KN.m) e. Girder shears at FG, GH, MN, and NO (KN) a.
20 kN.m 2 kN/m A- B CO 2m 4m 2m