A 6 in thick concrete wall, having thermal conductivity k =0.50 Btu/h. ft.° F, is exposed to air at 70°F on one side and air at 20°F on the opposite side. The heat transfer coefficients are h=2.0 Btu/h- ft².0 F on the 70°F side and = =10 Btu/h .ft².° F on the 20° F side. Determine the heat transfer rate
Q: In the special position shown for the log hoist, booms AF and EG are at right angles to one another…
A: Given: The log weight, W = 4800 lb
Q: Determine the force in member BC of the loaded truss. The force is positive if in tension, negative…
A:
Q: simply supported beam of length L and cons ed from the left end. The magnitude of maxin
A: given:y=woL4π2EIcosπxL
Q: Each of the blocks shown in figure (9.14) he The rear block moves with a speed of 2 m/= Front block…
A:
Q: square high-density polyethylene [α = 158×10–6/°C] plate has a width of 205 mm. A 123 mm diameter…
A: Given:α=158*10-6/°Cwidth, b=205 mmdiameter, d=123 mmIncrease in temperature, ∆T=45°C
Q: PROBLEMI.2 A HYDRAULIC TURBINE IS REQUIRED TO PRODUCE 800 KW POWER AT 500 RPM UNDER A NET HEAD OF 40…
A: For the prototype: Power = 800 kW Speed =500 RPM Head = 40 m For the model Head = 10 m Scale ratio =…
Q: An ammonia ice plant produces ice from water at 30°C to ice at -5°C. It works on standard vapour…
A:
Q: 3. a) For the following system, determine the flow rate in m3/s. b) Determine the relative density…
A: Given data: ◆ The difference in manometric fluid level: hmanometric = 0.5 m ◆ The diameter of pipe…
Q: ter flows through a spillway and goes through a hydraulic jum Flow rate Q=15m³/s per meter width of…
A: given:flow rate Q=15m3/sY1=0.6m
Q: A sailboat moving in the direction shown is tacking to windward against a north wind. The log…
A:
Q: A gasoline-powered engine runs in an Otto cycle with a compression ratio of CR = 9 : 1. The intake…
A:
Q: A flange bolt coupling consists of eight 0.375” diameter bolt on a bolt circle 11” diameter, and…
A:
Q: The system of four particles has the indicated particle ma positions, velocities, and external…
A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…
Q: The motion of a particle is defined by the relation x = at² - b(t -2)³ where x and t are expressed…
A:
Q: The normal strain in a suspended bar of material of varying cross section due to its own weight is…
A:
Q: A AISI 304 steel bar, 5 m long with square section (2x6 mm), is stretched by effect of a applied…
A:
Q: Casting is an engineering metal fabrication technique to produce com Classify FOUR (4) types of…
A: Casting:- Basically, it is a manufacturing technique where the liquid is heated and then poured into…
Q: moving in a circular onent of the accelerati 0, determine its velo problems:
A: given:radius of circular path r=100mat=t+1
Q: A thin rectangular polymer plate PQRS of width b = 360 mm and height a = 156 mm is shown in the…
A:
Q: 17. A mass weighing 8 lb stretches a spring 1.5 in. The mass is also attached to a damper with…
A: Given data: W=8 lbL=1.5 in=0.0381 m Need to determine the value of damping coefficient"γ".
Q: An object is dropped into a beaker of water. Two forces are operating on the object viz. the weight…
A: The buoyant force FB is the force exerted on a floating or submerged object in a static liquid. It…
Q: The answers should not be in vector form. Please re-anser. Rate will be given
A:
Q: Find the moment (Nm) acting at O due to all forces and couple present in the following system if P =…
A:
Q: A car starts from rest and travels along a straight track such that it accelerates at 6 m/s2for 12 s…
A:
Q: The 47-lb load is hoisted by the pulley system and motor M. The motor exerts a constant force of 40…
A:
Q: The driver of the truck has an acceleration of 0.45g as the truck passes over the top B of the hump…
A:
Q: A metal with an internal crack is loaded with a tensile stress of 20 MPa. If the crack length and…
A: Write the given data. σt=20 MPal=3.6×10-2 mmr=1.8×10-4 mmE=100 GPaγs=3.5 J/m2
Q: A thin triangular plate PQR forms a right angle at point Q. During deformation, point Q moves to the…
A:
Q: a = 1.7 ft, b = 3.4 ft, and c = 2.55 ft. P = 3000 lb box beam wall thickness, t = 0.610 in. diameter…
A:
Q: angular plate shown is subjected to a uniaxial developed on a plane forming an angle of 30° al area…
A: given:tensile stress σ=2000psiangle θ=300
Q: A particle moves that is defined by the parametric equations given below (where x and y are in…
A:
Q: True or False: All atoms tend to loseelectrons.
A: In this problem, it is asking that the given statement is True or False.
Q: Determine the moment of the 800-N force about point A and point O by Varignon’s theorem. Show…
A:
Q: The magnitude of the force Qis 821 N. Determine the magnitude of the moment (Nm) of Q about the line…
A:
Q: Solve the transfer function T(s) = x2/F(s) if b1 = 2, b2 = 4, K1 = 5 and k2 = 7 中 m X1 K3 = 6 b3 = 3…
A: For solution refer below images.
Q: Why might surface mining be less risky for miners than underground mining? OA. Surface miners use…
A: Surface mining is a method of extracting minerals from the surface of the Earth. Surface mine can be…
Q: Non-metallic materials such as composite materials are one of the emerging materials that are used…
A: Composite materials are the type of materials in which two or more materials are mixed to form a…
Q: View Policies Current Attempt in Progress Determine the force in member BE of the loaded truss. The…
A:
Q: QUESTION 4: NATURAL CONVECTION Two concentric spheres with diameters D₁ = 60 mm and Do = 100 mm are…
A: The process of transfer of heat which happens due to the movement of the fluid particles by means of…
Q: The 200 x 200 x 1,250-mm oak [E = 12 GPa] block (2) shown is reinforced by bolting two 5 x 200 x…
A:
Q: Consider a two-stage cascade refrigeration system operating between -80 o C and 80 o C. Each stage…
A: Refrigerant is R13 Single stage vapor compression cycle Maximum temperature = 80 oC Minimum…
Q: Generally, aircraft materials are required to be low density, excellent heat resistance and high…
A: Different alloys (except aluminum alloys) that are also used as aircraft materials is- Titanium…
Q: a large spherical ball oscillates up and down the water surface that creates the wave. the radius of…
A: Given : R = 1 m Volume immersed = 3/4 of volume of ball To find : Volume of freshwater displaced…
Q: A runner wants to finish a 576 m race in 68.4 seconds. He accelarates from rest and attained his…
A: Total race (DR)=576 mT=68.4 sect1=8.9 sec Need to determine the maximum constant velocity of the…
Q: Which of the following is(are) true regarding a 10' x 30'wall that has a 21-ft2 door and a 20-ft2…
A: Given that : H = 10 ft , L = 30 ft A1 = 21ft2 A2 = 20ft2. We need to find correct option given…
Q: Calculate the DOF (mobility). Show your accounting for L, J₁, J. Given: M-3(L-1)-2J₁-J
A:
Q: An inventor claims to have devised a refrigeration cycle operating between hot and cold reservoirs…
A: Given data as per question Temperature of hot reservoirs = 308 K Temperature of cold reservoirs =…
Q: The cantilever beam is subjected to a concentrated load of P-50 kips. The cross-sectional dimensions…
A: Given data: ◆ The load applied at the free end of the cantilever beam: P = 50 Kips ◆ The dimensions…
Q: An axial member consisting of two polymer bars is supported at C as shown. Bar (1) has a…
A:
Q: please answer asap! STATICS OF RIGID BODIES (Please write the complete solutions and FBD/Free-Body…
A:
Step by step
Solved in 2 steps with 1 images
- 1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.2.2 A small dam, which is idealized by a large slab 1.2 m thick, is to be completely poured in a short Period of time. The hydration of the concrete results in the equivalent of a distributed source of constant strength of 100 W/m3. If both dam surfaces are at 16°C, determine the maximum temperature to which the concrete will be subjected, assuming steady-state conditions. The thermal conductivity of the wet concrete can be taken as 0.84 W/m K.1.37 Mild steel nails were driven through a solid wood wall consisting of two layers, each 2.5-cm thick, for reinforcement. If the total cross-sectional area of the nails is 0.5% of the wall area, determine the unit thermal conductance of the composite wall and the percent of the total heat flow that passes through the nails when the temperature difference across the wall is 25°C. Neglect contact resistance between the wood layers.
- A plane wall 15 cm thick has a thermal conductivity given by the relation k=2.0+0.0005T[W/mK] where T is in kelvin. If one surface of this wall is maintained at 150C and the other at 50C, determine the rate of heat transfer per square meter. Sketch the temperature distribution through the wall.3.16 A large, 2.54-cm.-thick copper plate is placed between two air streams. The heat transfer coefficient on one side is and on the other side is . If the temperature of both streams is suddenly changed from 38°C to 93°C, determine how long it takes for the copper plate to reach a temperature of 82°C.2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
- A high-speed computer is located in a temperature-controlled room at 26C. When the machine is operating, its internal heat generation rate is estimated to be 800 W. The external surface temperature of the computer is to be maintained below 85C. The heat transfer coefficient for the surface of the computer is estimated to be 10W/m2K. What surface area would be necessary to assure safe operation of this machine? Comment on ways to reduce this area.2.46 The wall of a liquid-to-gas heat exchanger has a surface area on the liquid side of with a heat transfer coefficient of . On the other side of the heat exchanger wall flows a gas, and the wall has 96 thin rectangular steel fins 0.5 cm thick and 1.25 cm high as shown in the accompanying sketch. The fins are 3 m long and the heat transfer coefficient on the gas side is . Assuming that the thermal resistance of the wall is negligible, determine the rate of heat transfer if the overall temperature difference is .Show that the rate of heat conduction per unit length through a long, hollow cylinder of inner radius ri and outer radius ro, made of a material whose thermal conductivity varies linearly with temperature, is given by qkL=TiTo(rori)/kmA where Ti = temperature at the inner surface To = temperature at the outer surface A=2(rori)/ln(ro/ri)km=ko[1+k(Ti+To)/2]L=lenthofcyclinder
- 2.30 An electrical heater capable of generating 10,000 W is to be designed. The heating element is to be a stainless steel wire having an electrical resistivity of ohm-centimeter. The operating temperature of the stainless steel is to be no more than 1260°C. The heat transfer coefficient at the outer surface is expected to be no less than in a medium whose maximum temperature is 93°C. A transformer capable of delivering current at 9 and 12 V is available. Determine a suitable size for the wire, the current required, and discuss what effect a reduction in the heat transfer coefficient would have. (Hint: Demonstrate first that the temperature drop between the center and the surface of the wire is independent of the wire diameter, and determine its value.)A cooling system is to be designed for a food storage warehouse for keeping perishable foods cool prior to transportation to grocery stores. The warehouse has an effective surface area of 1860 m2 exposed to an ambient air temperature of 32C. The warehouse wall insulation (k=0.17W/(mK)) is 7.5 cm thick. Determine the rate at which heat must be removed (W) from the warehouse to maintain the food at 4C.2.34 Show that the temperature distribution in a sphere of radius . made of a homogeneous material in which energy is released at a uniform rate per unit volume , is