Answered: A 50cm long rod of 20mm diameter is…

A 50cm long rod of 20mm diameter is facing 100N compressive load. If the Poisson’s ratio is 0.85 and the final length is 40cm, what will be the final diameter?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 58 kN compressive load is applied to a 7 em diameter, 2 cm tall aluminium cylinder. Calculate…

A: Solution:- Stress:- The force per unit area, or intensity of the forces distributed over a given…

Q: Three proposed cross-section configurations for joining three boards are shown in Figure 1. Each…

A: Given, b = 50 + 29 + 9 = 88 mm Mz = 5000 Nm or 5 x 106 N-mm

Q: When solving the problems for Section 1.6, assume that the material behaves linearly elastically.…

A: Given data in question Diameter Elasticity modulus Poissons ratio To find out Largest force P

Q: As shown, a hole is to be punched out of a plate having a shearing strength of 60 ksi. The…

Q: 8: A thin cylindrical has inner radius=450 mm, thickness=9 mm is subjected to internal Pressure of…

A: Given data : Radius (r)=450 mmInternal pressure (p)=20 MPaThickness (t)=9 mm

Q: emperature when this system was assembled was 74F, what would be the stress in a temperature of 4OF?…

A: According to given data The assembly below will be used for each problem Lengths, diameters, and…

Q: Ex 5.2: Calculate the lateral strain for a mild steel rod subjected to an axially load causing an…

A: Introduction : The given question is related with solid mechanics . In this question we are provided…

Q: QI: A circular concrete reservoir (tank) of 10.6 m internal diameter, 11 m outer diameter and 4 m…

A: "Since you have question with multiple sub-parts, we will solve the first sub-part for you. Please…

Q: The figure below shows a shaft of three segments It is restrained (fixed support) at both sides and…

Q: As demonstrated, four 25mm diameter rivets with a T=75kN axial load are equally distributed. The…

A: Shear stress in rivets: The plates are connected by rivets happens to exert tensile stress on the…

Q: A compressive force P is applied to a 75mm by 100mm piece of wood. The wood grain makes a 20- degree…

A: To determine the largest axial load P that can be safely applied to the wooden column. Given,…

Q: A steel [E=200 GPa] rod with a circular cross section is 11 m long. Determine the minimum diameter…

Q: A beam has a cross-section that is 11inches tall and 4inches wide. If the max shear in the beam is…

A: Given Load 8 kipsDepth 11 inWidth 4 inTo find out Maximum shear stress

Q: Challenge Problem 6: A 3/4 in. diameter punch is used to punch a hole through a steel plate 1/2 in.…

A: Given Load 60,000 lbDiameter 3/4 inThickness 1/2 inTo find out Shear stress

Q: A hollow circular column of steel (E = 30,000 ksi) is subjected to a compressive load P. The column…

Q: A hollow cylinder with an OD of 100mm and an ID of 30mm, supports a load of 100kN. What is the…

Q: A wood beam carries the loading shown in the figure. Calculate the magnitude of the bending stress…

A: Given data: P = 4467 N, W= 1887 N/m, a = 1.12 m, b = 2.46 m, c = 1.27 m, Width of beam = 79 mm…

Q: A steel tower of a suspension bridge is designed to stand 250 feet tall. The forces from the cables…

A: The Young modulus of elasticity of steel given is , E=30000 Ksi the length of steel tower, L = 250…

Q: A horizontal 50 kN load is applied on a 610UB125 Beam as shown in Figure 4. Determine the stresses…

Q: In the figure below, the wood pole is supported by cables of 0.32-in diameter. The turnbuckles in…

Q: A wood beam 150 mm wide by 300 mm deep is loaded as shown in the figure. If the maximum flexural…

Q: Determine the maximum shear stress formed in 200-mm diameter shaft

A: GIVEN- A FLANGED BOLT CINNECTION CONSISTING OF 10 BOLTS. REQUIRED-TO FIND MAXIMUM SHEAR STRESS IN…

Q: A high-strength steel band saw, 26 mm wide, runs over pulleys 1200 mm in diameter. What minimum…

Q: (c). A bar of length_1000 mm and diameter 30 mm is centrally bored for 400 mm, the bore diameter…

A: Given data Load Change in length Length Diameter Bore length Bore diameter

Q: A steel [E = 200 GPa ] rod with a circular cross section is 20 m long. Determine the minimum…

Q: Calculate the hoop stress in a 0.9m diameter pipe with a 2mm wall thickness, subjected to a 100PA…

A: Introduction- When pressure is applied to a pipe, hoop tension develops along its circumference. The…

Q: What is the shear stress (in psi) in a steel sheet (thickness is 0.094 in) of the slug that has the…

Q: strength of materials... answer only A wood beam carries the loading shown in the figure. calculate…

A: Given data: UDL = 2349n/m PL= 5381N

Q: Steel railroad rails 10m long are laid with a clearance of 3mm at a temperature of 15°C. The modulus…

A: Given data, Length of rail = 10 m Clearance = 3 mm Initial temperature = 15 °C E = 200 GPa Final…

Q: In the figure below, the wood pole is supported by cables of 0.32-in diameter. The turnbuckles in…

Q: Consider the T-beam shown in (Figure 1). Take wy 18 kN/m and toy-27 kN/m Figure 200 mm C 200 mm 20…

Q: The thin-walled vessel shown is fabricated by joining two cylinders with thickness 26 mm using 20…

A: Given, Thickness of the vessel, t= 26mm Number of bolts= 20 Diameter of the bolts= 20mm Outer…

Q: LOmPa aGMPa 30 MPa

A: Solution Given Data σx=30 MPaσy=10 MPaζxy=26 MPa

Q: 02 Determine the smallest allowable điameter brass rod, of length 3.Om, if the rod is to be twisted…

A: We need to find smallest allowable diameter of brass rod.

Q: A steel rod of original length 200 mm and final length of 200.2 mm after application of an axial…

Q: PROBLEM 4: The figure shows a plate that is fastened to a fixed to a fixed member by five 12-mm-…

Q: As shown in the figure, if the area of the member of the truss for tension is 300 square millimeter…

A: To find out the stress in each bar.

Q: A 3ft long bar with a 1in x 1in cross section is subjected to a 14,153lb tensile load. What is the…

A: Area of cross section ( A ) = 1 in2Tensile load (p ) = 14153 lb Tensile stress = ? Ksi

Q: A HOMOGENOUS 800 KG BAR AB IS SUPPORTED AT EITHER END BY A CABLE AS SHOWN IN THE FIGURE. CALCULATE…

Q: Ex 5.2: Calculate the lateral strain for a mild steel rod subjected to an axially load causing an…

Q: Steel: A = 500 mm? P Timber: 4P A = 2000 mm

Q: Given a cantilever beam with given loadings and cross-section as shown in the figures, what is the…

A: what is the absolute value of the maximum flexural stress? (in MPa)??

Concept explainers

Pressure and Stress

Question

100%

A 50cm long rod of 20mm diameter is facing 100N compressive load. If the Poisson’s ratio is 0.85 and
the final length is 40cm, what will be the final diameter?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

what is the loading in pounds that you need to achieve vertical stress of 15 psi? Assume all the loading will put on the one-to-one ratio hanger. Assume a diameter of 2.5in.
Problem 6: The compound bar containing steel, bronze, and aluminum segments carries the axia! loads shown in the figure. The properties of the segments and the working stresses are listed in the table. Steel 2 ft Bronze 4 ft A (in.²) E (psi) o, (psi) Aluminum 3 ft 2P Steel 0.75 30 × 106 20 000 Bronze 1.00 12 x 106 18 000 4P Aluminum 0.50 10 x 106 12 000 Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 in. and the working stresses are not to be exceeded.
Assignment Problem 10.1. A steel bar of diameter d = 52 mm is twisted by torques at the ends. The allowable shear stress is 65 MPa. What is the maximum torque that can be applied?
Please help me solve this problem. Need it asap. Thank you.
Problem 1: The assembly below will be used for each problem. Lengths, diameters, and materials are provided. If the temperature when this system was assembled was 74F, what would be the stress in each cylinder at a temperature of 40F? Problem 2: If the fixed support at D were removed and the temperature change did not occur, how far would point D move if a 400 lb tension load was applied at the center of each cylinder? (Hint: what sections would you break up the assembly into to find the Normal forces?) Problem 3: Based on the results from problem 2 and the sections specified in your solution, how much would the diameter of each section shrink from the loads applied? (Hint: Look at Poisson’s ratio for each of the sections listed.
1) A brass pipe with a 0.5inch inside diameter and 1/16 inch wall is twisted using a 14inch long pipe wrench. If a load of 74 lbs is applied perpendicularly to the end of the wrench. If the E of brass is 14.6x10^6 psi, what is the max torsion stress in the pipe? • Find the outside diameter of the pipe using the ID and given wall thickness. • Find the polar moment of inertia of the cross-section of the pipe. • Find the torque being applied to the pipe, via the wrench. • Use the torsional stress equation to find the requested stress. Compare your answer: Max Torsional Stress 36.61 ksi
Determine maximum shear stress
Show your detailed, clear, and whole solution. Thank you.
A steel I-beam has a web that is 17inches tall and 0.19inches thick. If the max shear in the beam is 6kips, what is the approximate max shear stress in the beam in psi? Type your answer...
STRESSES 1. A 150mm x 50mm board is glued to a triangular board. Determine the maximum shear stress of the adhesive IN BEAM material used to connect the boards. 20 KN 1 m 30 KN/m 150 mm 50 mm 1 m 1 m 15 KN/m 250 mm 15 KN/m 2 m 350 mm
32 H.W tind longitudinal and hoor tensile stresses in the Wall of vessel Shown in figure, if the internal Bessure is 0.9 Ma and thickness of Wall is 6.4 mm? Ansi é =42.19 MPa + F= 62.8 Ma Also find ?5067 0.6m 0.6m
A 3-m long steel plate having a cross-section of 25 mm x 300 mm is used as a hanger and subjected to a tensile load of 1070 kN. Poisson’s Ratio = 0.25 and E = 200 000 MPa. Compute the lateral strain. Express your answers in 6 decimal places.