A 50-m steel tape weighs 1.05 kg and is supported at its endpoints and the 10-m and 25-m marks. If a pull of 6.0 kg is applied at the ends of the tape, what is the correction due to sag for a full tape length? a. 0.060 m b. 0.064 m c. 0. 050 m d. 0.500 m

A 50-m steel tape weighs 1.05 kg and is supported at its endpoints and the 10-m and 25-m marks. If a pull of 6.0 kg is applied at the ends of the tape, what is the correction due to sag for a full tape length? a. 0.060 m b. 0.064 m c. 0. 050 m d. 0.500 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Blocks A and B weigh 30 lb and 50 lb, respectively. В M = 0.5 %3D 20° MBA = 0.6 C D MẠC = 0.4 If the…

Q: The square steel plate has a mass of 1920 kg with mass center at its center G. Calculate the tension…

Q: For the frame shown in the figure, The beam has a plastic moment of 750 kN.m and the columns have a…

A: MP = 750KNm MP' = 375KNm

Q: A 50-m steel tape weighs 1.05 kg and is supported at its endpoints and the 10-m and 25-m marks. If a…

Q: sagi 3.26 A distance of 72.55 ft is recorded using a steel tape supported only at the ends with a…

A: To find out the corrected distance for sag.

Q: A two points want to be fixed on the ground with a slope of 6 % with horizontal distance of 265 m. A…

Q: A steel rod has a hexagonal cross section with 10 mm on each side. If the working stress is 110…

A: solutionGiven working stress σ=110 MNm2=110 Nmm2cross section is hexagon of side a= 10mm each

Q: shear force on bolt A.

A: Given:- d=1.25inch To find:- a) vertical deflection b) shear stress c)shear force on bolt A

Q: Help me, thank you! A 100- m steel tape is used to measure the distance of the line and found to be…

A: Surveying mainly considers the branch of measurement of the points on the ground surface for the…

Q: Consider the plate subjected to the four external loads shown. Calculate an equivalent force couple…

Q: 20 kN.m 2 kN/m A- 2m -4m -2m- Which of the following best describes the elastic curve (deformed…

A: Finding out deformed shape of the beam.

Q: force, F = 51 kN) inclined at an angle alpha = 30 degrees from the vertical, such that it is in…

Q: DETERMINE THE VALUE OF "P" SUCH THAT RAY IS TWICE AS MUCH THE VALUE OF RBY. DEFINE THE VALUES OF…

Q: The measured length of an inclined distance was recorded to be 600.00 m long. The difference in…

A: The measured inclined length = 600.00m long Measured at temperature 25 0C The difference in…

Q: P-

Q: A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall…

A: Since the only question is to find the maximum moment We will draw shear and bending moment diagram…

Q: Ex-5. A steel tape is standardized at 68°F under a tension of 15 lb when supported at the two ends…

Q: A 30-m tape weighs 12.5 g/m and has a cross-section of 0.022 cm?. It measures correctly when…

Q: Analyze using flexibility Method 2K/H 2 кун нигде 12 A pom To Dsi O = 1 ** B FI=Constant

Q: What does the variables stand for and assumption is valid ?

A: Stress strain diagram for singly reinforced beam

Q: Hello, can someone help me with this pls. Determine the vertical component of the force applied at…

Q: Calculate the maximum normal bending stress and the maximum shear stress

A: A beam is said to be in pure bending if the bending moments are exclusively along the axis of the…

Q: Use:E= 200 000 MPaI- 500 mm 120 kNim 120 kN/m -20m- -20m 20m

A: According to given data E= 2000000 MPA

Q: a- 33.8 kN, b 27.2 kN, 48 m kN D " KN " kN 4 m 5m A. - 40 x 10 mm A- 60 x 10 mm A- 40 x 10 mnm…

Q: 19 What is the shear force value (kNm) at support A? 5 KN/m 4 m

A: Given:- A beam is given with uniformly distributed load of 5 kN/m acting on it Support A is hinged…

Q: Problem 3 Five forces are acting on the cantilever beam AB. Find the resultant or a couple acting on…

Q: 1. The Block shown are connected by flexible inextensible cord passing over frictionless. pulleys.…

Q: A 50 m steel tape is used to measure a rectangle at 20°C with a pull of 55 N. The sides are recorded…

A: Since the temperature at the time of measurement is higher than that of standard temperature. The…

Q: The continuous beam shown below has an internal hinge at point C. The beam is loaded with two…

A: To determine:1) the vertical deflection at C2) the vertical deflection at F3) the rotation at A4)…

Q: 9- www d D F e

Q: A 30-m steel tape weights 1.05 kg and is supported at its end points and the 10-m and 25-m marks. If…

Q: Detemine the plastic moment strength (kN-m) of a C15x50, A36 steel, about the minor axis. d= 381 mm…

A: section : c15×50 plastic moment of section (Mp)?

Q: PROBLEM 3: The coefficients of friction between the block and the rail are u, and µ. Determine the…

Q: Ex-6. A steel tape with a cross-sectional area of 0.039 cm2and weighing 0.909 kg has a length of…

A: Given Cross section area=0.039cm^2 Weight=0.909kg Length=30.009m Tm=20℃ Ps=5.5kg Slope=4% PT=12kg…

Q: Ex-6. A steel tape with a cross-sectional area of 0.039 cm? and weighing 0.909 kg has a length of…

A: We have to determine the corrected horizontal distance

Q: Q1/ A beam carries the loads shown in figure, if the tensile stress must not exceed 20 MPa and the…

Q: The 609-N force is applied to the 112-kg block, which is stationary before the force is applied.…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

0.060 m

0.064 m

0. 050 m

0.500 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please solve it correctly
Find the value q can take so that the BD bar, the cross section of which is shown in the figure, can carry the given load without buckling. factor of safety n = 3 Ri= 7cm , Rd=9cm on BD bar
4. A 375.00 ft. line is to staked-out with a steel tape (fully supported) inside a warehouse. The tape is to be pulled at 10 lb. The tape is known to be 100.012 ft. long when pulled at 25 lb at 68 degrees F. The tape weighs 1 lb. The cross-sectional area of the tape is 0.0030 sq. in. The elastic modulus is 29,000,000 psi. The temperature inside the warehouse is 68 degrees. What distance on the tape must be used to stake the line?
The measured length of an inclined distance was recorded to be 425.00 m long. The difference in elevation between the initial and end points was found to be 1.19 m. The 25 m tape is of standard length at temperature 20 °C. During measurement the temperature reading was 23°C. The tape was raised above ground and supported at both ends with an applied pull of 13kg, which may cause the tape to sag. The tape has a weight of 0.06 kg/m. (K=0.0000116 m/°C) Determine the corrected horizontal distance (in meters)
3 & 4 pls
A metallic cantilever 150 mm wide, 200 mm deep and 2 m span carries a uniformly varying load of 50 kN/m at the free end to 150 kN/m at fixed end. What will be deflection at the free end. [Take E = 100 GPa] %3D
DETERMINE THE VALUE OF "P" SUCH THAT RAY IS TWICE AS MUCH THE VALUE OF RBY. DEFINE THE VALUES OF SUPPORTS. 4.50 KM/m •ZKYM ZKN 1A 2.25m 0.00m 0.50 m 0. 20 0.75m P XB
Solve correctly
Ex-6. A steel tape with a cross-sectional area of 0.039 cm²and weighing 0.909 kg has a length of 30.009 m. when supported throughout 20°C and subject to a tension of 5.5 kg. This tape is used to measure a distance along a uniform 4% grade and is supported throughout during the measurement. The tension applied is 12 kg. The temperature of the tape is 2°C. The measured slope distance is recorded 381.615 m. What is the corrected horizontal distance? AMa
Ex-6. A steel tape with a cross-sectional area of 0.039 cm²and weighing 0.909 kg has a length of 30.009 m. when supported throughout 20°C and subject to a tension of 5.5 kg. This tape is used to measure a distance along a uniform 4% grade and is supported throughout during the measurement. The tension applied is 12 kg. The temperature of the tape distance is recorded 381.615 m. What is the co 2°C. The measured slope ected horizontal distance?