sagi 3.26 A distance of 72.55 ft is recorded using a steel tape supported only at the ends with a tension of 15 lb and weighing 0.016 lb per foot. Find the distance corrected for sag. 3.27

Q: 10 Kips 10 Kips.ft A C D E.

A:

Q: Question 2: Determine the horizontal displacement of point C. El is constant. Using the method of…

A: The length of the member AB(LAB)=10 ft, The load on the member AB(PAB)=400 lb/ft, The length of the…

Q: Clarification: "AP" indicates the coordinates of point A

A: To determine the central axis of the system of sliding vectors, let's break down the problem step by…

Q: 30 kN 50 kN to B D A 1 m 3 m 2 m Figure P-403

A:

Q: USE DOUBLE INTEGRATION METHOD. From the given determinate beam, which of the following provides the…

A:

Q: a) top most, lef tmost FIND: 6) botton-most, right-most 3cm S.ם r = 1,25 y 125 } 05 Vb cm 1.5 3 I…

A:

Q: Find the displacement Bx, By, Gy, and Cx by Virtual Work. A B D 5 kips 20 kips C H ↑G 15 kips k 20…

A:

Q: Compute the vertical displacement at joint G. the area of all bars A = 5 in?, and E = 29,000…

A: The virtual work method, also known as the virtual force method or the unit-load method, is a means…

Q: When azimuth of AB direction (AB) = 43.287 and B = 137,5593 are given find the azimuth of (BC).…

A: Given Azimuth of AB = 43.287o Internal angle = 137.5593o   To find Azimuth of BC

Q: Solve the following armature using the virtual work method, Taking into account E = 29x103 K / in2,…

A: We have used the following data 1 plug 2 = 1 inch2  1 pies= 1 feet  E= 29×103 ksi

Q: 3. Calculate horizontal displacement of C ( El=constant) D

A:

Q: Using the method of virtual work, find the vertical displacment of Point D. E = Ksi 1 inz 29,000…

A: To find the vertical displacement at the point D in the given truss using the method of Virtual…

Q: Given the vectors M = and N = , find a) unit vector in the direction of -M + 2Ñ; b) magnitude of 5î…

A:

Q: am shown, use double integration method to slope at "B" ite steps) 201 EI = Constant EI dy = ±EI

A:

Q: Use conjugate beam method to determine the slope at C. Where El=100,000KN/m^2 1OOKN A AAm C RB

A: In conjugate beam method Slope at any section in real beam is equal to shear force at that section…

Q: c. Consider the function y=x" 1 D Sketch It. 2. For the function determined in part (1), consider a…

A: | 8 | * 4 | * 0 | *…

Q: What is the allowable bending strength (ASD) of the cantilever beam shown below considering the…

A:

Q: Determine the forces in members CD, CJ, and DJ. M 6' A L B L 6 panels at 2¹ K C L J D L I E L H F L…

A: Solution: Compute the angle: tan θ=42=2θ=tan-12θ=63.43 RA+Iy=6L Taking moment @ A:…

Q: Compute the flexural stress (MPa) in the steel for the beam shown using transformed-area method.…

A: Given : Area of one bar of 36 mm in tension zone = 1006 mm2Numbers of bars in tension zone = 4Total…

Q: 14. The moment of inertia about x-axis for rectangular area A = (20 x 10) in2 is: %3D

A: Option 2 is correct

Q: Determine the vertical displacement at c by used Virtual Work method. Dont calculate the EI Ans Acy…

A: Determine the vertical displacement of the joint C using virtual work method.

Q: H.W 1) find the slope and y-intercept for the line 2y+2x=4 2) find the radius and coordinate center…

A:

Q: 40 kN 15 kN/m EI EI 30 kNm B. 3m A 6m

A:

Q: 4) Solve the following armature using the virtual work method, taking into account A = 3.2 in2, E =…

A:

Q: Problem no. 2: The width of a river being observed is 75 m. Assuming the transit being used has an…

A: This problem is related to Surveying Engineering. In this problem Tacheometry surveying , Horizontal…

Q: USE DOUBLE INTEGRATION METHOD. From the given determinate beam, which of the following provides the…

A:

Q: Determine the sum of the moments created by the forces shown in the accompanying figure about points…

A:

Q: Determine the slope at point D of the beam shown using the Virtual Work Method. (You can verify…

A: Find the reactions of the orginal beam:∑ MA=0RB10-1505=0RB=75KN∑ Fy=0RA+RB-150=0RA=75KNMoment…

Q: Q2\ Use the virtual work method to find the vertical and horizontal displacement at joint D. 30 KN…

A:

Q: Use virtual work to find the displacement at point C

A: We will apply unit load at C.

Q: Mannings equation can only be used to find one value of velocity at a time. True False

A: Given data in question Mannings equation  To find out  Is the given statement true or false Note V =…

Q: Determine the horizontal displacement at A. Take E =199947.9615 MPa The moment of inertia of each…

A: Horizontal displacement at A

Q: Prove Δv/v = Δe/1+e

A: General formula for settlement due to compaction:

Q: Use the principle of virtual work. 300 N/m 3m 400 N

A:

Q: Question - (а) frame in the following figure (EI = constant, no need to find the final answer)…

A: NOTE - : Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: 1. Determine the slope and displacement of point C. El is constant. Use the method of virtual work.…

A: Given data  E = 70 GPA = 7 × 104 N/mm2  I = 5 × 108 mm4

State Plane Coordinate Systems

The state plane coordinate system (SPCS or SPS) is a collection of 124 coordinate systems or geographic zones prepared for particular regions of the U.S. Every state consists of one or more than one state plane zone, the boundaries of which generally follow the county lines. Inside the U.S., there are 110 zones in total, 10 more zones in Alaska, 5 in Hawaii, and 1 for Puerto Rico and US Virgin islands. The system is extensively used for geospatial and geographic data assembling by the state and local governments.