A 5.8m simple beam carries a uniform ultimate load Wu. The beam is compact with lateral supports only at end points. The properties of the section are: rts=29mm, ho=274mm, c=1.0, J=90,782 mm4, Zx=355x103mm3 , Shape Factor, SF=1.15, Lp=1,420mm, Lr=8,594mm, Cb=1.15 and Fy=248MP.. Calculate the design strength of the beam in KN-m. Express your answer in 3 decimal places

A 5.8m simple beam carries a uniform ultimate load Wu. The beam is compact with lateral supports only at end points. The properties of the section are: rts=29mm, ho=274mm, c=1.0, J=90,782 mm4, Zx=355x103mm3 , Shape Factor, SF=1.15, Lp=1,420mm, Lr=8,594mm, Cb=1.15 and Fy=248MP.. Calculate the design strength of the beam in KN-m. Express your answer in 3 decimal places

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam shown below, compute the following: Assume El = 1 X 10³ N-m² W = 300N/m 1.5m 0.5m 2m R1 (16-20) Compute the mid-span deflection y = (21-25) what is the max. deflection Ymax = mm R2
Please determine the beam shearing stress, flexural stress and maximum deflection using the given steel I beam.
The following are the properties of a steel section to be used for a beam section:Fy = 248 MPa Area = 21300Ix = 300000000 Iy = 98800000Sx = 2080000 Sy = 746000d = 289 tw = 19.2tf= 31.8 bf = 265w beam in kN/m = 9laterally unsupported length, Lb = 3 m 1. What is the minimum unsupported length of the beam to be considered long? a. 16.2 m b. 14.5 m c. 13.6 m d. 12.8 m 2. What is the critical depth over thickness ratio set by NSCP? a. 206.68 b. 126.68 c. 106.68 d. 16.68 3. What is the allowable bending stress in the given beam section? a. 148.8 b. 163.68 c. 142.68 d. 124.68 4. If the laterally unsupported length been 10 m, what is the allowable bending stress as per NSCP 2001? a. 148.8 b. 163.68 c. 142.68 d. 124.68
600 150 150 Refer to the figure shown. Given are the following: Unit weight of concrete = 24 kN/m fe' = 35 MPa fse = 820 MPa fpu - 1,350 MPa Aps = 1,200 mm? foy = 1.080 MPa Beam is a simple span and have a length = 30 m. Determine the design moment capacity of the section. (kN-m) 00L
A cantilever beam having a 4m span carries a uniformly distributed load throughout its length. The beam is A36 steel with yield strength Fy = 248 MPa. The beam is not restrained against lateral buckling. The beam is W 21 by 62 steel shape, whose relevant properties are shown below: r = 0.053 m d = 0.533 m bf = 0.210 m tf = 0.016 m S = 0.002077 m3 Given this condition, solve for the allowable flexural stress in the compression flange. Use Cb = 1 as should be taken conservatively
(3) 24 B Bean AB A Beam AB. 301 G 4#8 12" 24' -#4 24" Given fé= 3 ksi Grade 60 steel NWC. COVER = 1.5" #4 stirrups. DL= 70 psf, not including self-weight. LL = 40 psf. (No Live Load 4 # 8. b=12", h=24", Reduction
Determine the maximum load that an 8 foot long 2"x4" rectangular aluminum alloy bar (E = 10.5x10^3ksi, σY = 40 ksi) can support with a factor of safety of 3 for both crushing and buckling if it has endconditions of:a. Pinned-pinned.b. Pinned-fixed.c. Fixed-free.d. Fixed-fixed.
Steel Design W21x62 steel is used as a beam simply supported over a span of 8 m. The beam is laterally unsupported over the entire span Fy = 250 MPa. The properties of the section are as follows: Depth, d = 533 mm Flange width, bf = 210 mm Flange thickness, tf = 15.6 mm Web thickness, tw = 10.2 mm Radius of gyration, rT = 53.34 mm Section modulus, Sx = 2,077 x 103 mm³ a) Determine the value of the ratio L/rT. b) Determine the allowable bending stress in MPa.
A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 7 m long, pinned at the top fixed at bottom, and has additional support in the weak direction 3 m from the top. Properties of the section are as follows: A = 14,500 mm^2 Ix = 258.6 x 10^6 mm^4 Iy = 84.375 x 10^6 mm^4 1. Calculate the critical slenderness ratio of the member. a. 26.208 b. 45.882 c. 36.706 d. 27.529 2. calculate the nominal axial load capacity of the column a. 3104 kN b. 4851 kN c. 4213 kN d. 5344 kN 3. calculalte the service axial dead load if the service axial live load is twice as that of the dead load. Use LRFD. a. 1354 kN b. 992 kN c. 1093 kN d. 634 kN
A W420x85 steel beam is fully restrained with a uniformly distributed live load of 25 kN/m. The beam has a span of 10m. Use A36 steel. Properties of W40 x 85 A = 10839 mm2 %D bf = 180 mm tf = 18 mm %3D tw = = 11 mm Ix = 310 x 106 mm4 %3D d = 420 mm (Note: Since this is a built-up section, for checking of web slenderness, use h = d - 2t;) %3D 1) Calculate the design shear strength of the section. Check if the section is adequate in shear. USE LRFD and U = 1.2D + 1.6L. %3D 2) Is the maximum deflection at the midspan of the beam due to live load adequate? 3) Calculate the maximum uniform live load that can be carried by the beam.
Giv me all right solutions with clear calculations.