A 5 m high retaining wall having a smooth vertical back face retains a layered horizontal backfill. Top 2 mthick layer of the backfill is sand having an angle of internal friction, 0 = 30° while the bottom layer is 3 mthick clay with, C = 30 kPa. Assume unit weight of sand and clay as 20 and 18 kN/m3 respectively. Thetotal passive earth pressure per unit length of the wall is,kN/m.

Answered: Image /qna-images/answer/4bcd5382-9640-44c9-9e52-ed024678839a.jpg

A 5 m high retaining wall having a smooth vertical back face retains a layered horizontal backfill. Top 2 m thick layer of the backfill is sand having an angle of internal friction, = 30° while the bottom layer is 3 m thick clay with, C = 30 kPa. Assume unit weight of sand and clay as 20 and 18 kN/m3 respectively. The total passive earth pressure per unit length of the wall is kN/m.

A 5 m high retaining wall having a smooth vertical back face retains a layered horizontal backfill. Top 2 m thick layer of the backfill is sand having an angle of internal friction, = 30° while the bottom layer is 3 m thick clay with, C = 30 kPa. Assume unit weight of sand and clay as 20 and 18 kN/m3 respectively. The total passive earth pressure per unit length of the wall is kN/m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A retaining wall with a smooth vertical back retains a purely cohesive fill. Height of wall is 12 m. Unit weight of fill is 20 kN/m3, cohesion is 1.5 N/cm2. Assume tension cracks are developed. Mark the correct statement(s) about earth pressure. A Active thrust acting on wall is 1102.50 kN/m. Correct Option Depth of active thrust acting on wall is 6 m. C Active thrust acting on wall is 112.39 tonne/m. Correct Option Depth of active thrust acting on wall is 3.5 m from base. Correct Option B
A cantilever retaining wall supports 2 layers of soil and surcharge as shown below. The layers have these properties: Layer 1: 1.8m thick. γ = 17.4 kN/m3 and ϕ = 22 degrees Layer 2: 4.2m thick. γsat = 18.1 kN/m3 and ϕ = 30 degrees The angle of friction between the base and soil is 42 degrees. Unit weight of concrete is 23.6 kN/m3 What is the design moment (kNm / m) at the bottom of the stem? None of the choices 819.98 478.88 363.00 299.30 Please answer this asap. For upvote. Thank you very much
An 8 m tall retaining wall holds cohesionless sand with a density and angle of internal friction of 1.85 Mg/m3 and 33°, respectively. If the surface of the backfill slopes upwards at 86° to the vertical, Use Rankine’s conditions to find the force per unit length of the wall and its location for (a) Active State (b) Passive State Please draw the pressure diagram neatly for both cases
Given: → 4.5-m high retaining wall . Retaining homogeneous satorated soft clay. O'sat= 19.6 kNĪm³ Cu = 19.3 kN/m² ( undrained shear strergth) -> Diagram: Sopt Clay sat - 19.6 kN/m? Cu- 19.3 kN/m³ 4.5-m Make the necessary calu lation and draw the varialion of Rankine's active pressure on the wall with depth. nclude #te pressure from a waker-filled crack in - Find the depth up to which a tensile crack can occur. Delermink the total active force per unit lengh of the wall bepore the tensile crack gccurs. Assome tension stresses exist ard do not include the force from waler - filled Crack. - Delermine the tolal active force force per wall after the tensile crack occurs. 'Also, find Hhe locathon of the resultant. Neglect tersion shresses and include the force from the wafer-pilled crack. Find: your drawings unit lergth op the
A rigid retaining wall of 6 m height (Fig. Ex. 11.11) has two layers of backfill. The top layer to a depth of 1.5 m is sandy clay having = 20°, c = 12.15kN/m² and y 16.4kN/m³ The bottom layer is sand having = 30°, c =0, and y = 17.25kN/m³Determine the total active earth pressure acting on the wall and draw the pressure distribution diagram. 1.5 m 6 m GL c= 12.15 kN/m² 1.5 m y = 16.4 kN/m³ y = 17.25 kN/m³ = 30°,c=0 FE Sand 4.5 m TAVIAVAVAVAVA Sandy = 20° clay 8.2 kN/m² Figure Ex. 11.11 -34.1 kN/m².
A retaining wall with a smooth vertical back retains sand backfill for a depth of 6m. The horizontal backfill has the following properties. d' = 0, y = 16KN/m³; Vsat = 20k N/m³. Calculate the magnitude of total thrust against the wall for given conditions: (a) backfill fully drained but the top of wall is restrained against yielding: (b) backfill fully drained and the wall is free to yield, and (c) wall free to yield, water table at 3m depth without drainage. Determine the point of application for the resultant thrust case(c).
The following figure shows a section of an anchored retaining wall embedded into a saturated stiff clay layer. The sand has a unit weight of = 18 kN/m³, c' = 0 kPa and o' = 34º. The clay has a unit weight of = 20 kN/m³, c₁ = 80 kPa and = 0°. A uniform pressure of 40 kPa is applied on the soil surface. The short term stability of the wall is considered in an undrained analysis. Use the Rankin's theory of lateral earth pressure to determine the active and passive horizontal stresses. You should apply the requirements of AS 4678 and the partial factors of safety method in estimation of soil pressures. Assume the soil is in-situ and use a structural classification factor of ₁ = 1. 3m 1m Water table 1.5m 40 kPa Not to Scale Sand Clay Ta
A vertical retaining wall 8.8 meters high retains a horizontal backfill having the following properties: Void ratio = 0.64; Specific Gracvity = 2.64; Water Content = 28 %; Angle of internal Friction = 31°. Compute the location of the active force in meters from the bottom of the wall acting on it if the water table is 3.0 meters below the ground surface.
5min Thanks for help