A rigid retaining wall of 6 m height (Fig. Ex. 11.11) has two layers of backfill. The top layer to a depth of 1.5 m is sandy clay having = 20°, c = 12.15kN/m² and y 16.4kN/m³ The bottom layer is sand having = 30°, c =0, and y = 17.25kN/m³Determine the total active earth pressure acting on the wall and draw the pressure distribution diagram. 1.5 m 6 m TAVIAVAVAVAVA Sandy = 20° c = 12.15 kN/m² 1.5 m clay y = 16.4 kN/m³ y = 17.25 kN/m³ = 30°,c=0 FE 4.5 m GL Sand 8.2 kN/m² Figure Ex. 11.11 -34.1 kN/m².

A rigid retaining wall of 6 m height (Fig. Ex. 11.11) has two layers of backfill. The top layer to a depth of 1.5 m is sandy clay having = 20°, c = 12.15kN/m² and y 16.4kN/m³ The bottom layer is sand having = 30°, c =0, and y = 17.25kN/m³Determine the total active earth pressure acting on the wall and draw the pressure distribution diagram. 1.5 m 6 m TAVIAVAVAVAVA Sandy = 20° c = 12.15 kN/m² 1.5 m clay y = 16.4 kN/m³ y = 17.25 kN/m³ = 30°,c=0 FE 4.5 m GL Sand 8.2 kN/m² Figure Ex. 11.11 -34.1 kN/m².

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

3. Draw the pressure diagram of the retaining wall with the soil profile shown both in active and passive cases. Solve for the active and passive lateral force and its location from the bottom of the wall. 4.5 KPa Gs = 2.73 e = 0.67 Ø = 27° C =0 KPa %3D 4m Gs = 2.66 %3D e = 0.85 Ø = 34° C = 5 KPa 6m
Q-Retaining walls- A 6 m high retaining wall with a vertical back has a backfill of silty sand with a slope of 10° for the backfill with values of KH = 760 kg/m²/m and Ky =100 kg/m²/m, the total active earth pressure will approximately be.
Given: → 4.5-m high retaining wall . Retaining homogeneous satorated soft clay. O'sat= 19.6 kNĪm³ Cu = 19.3 kN/m² ( undrained shear strergth) -> Diagram: Sopt Clay sat - 19.6 kN/m? Cu- 19.3 kN/m³ 4.5-m Make the necessary calu lation and draw the varialion of Rankine's active pressure on the wall with depth. nclude #te pressure from a waker-filled crack in - Find the depth up to which a tensile crack can occur. Delermink the total active force per unit lengh of the wall bepore the tensile crack gccurs. Assome tension stresses exist ard do not include the force from waler - filled Crack. - Delermine the tolal active force force per wall after the tensile crack occurs. 'Also, find Hhe locathon of the resultant. Neglect tersion shresses and include the force from the wafer-pilled crack. Find: your drawings unit lergth op the
Considering that the horizontal thrust from the back of a 5.5 m wide brick wall to the 1 m deep part of the wall is H = 55 kN a) Find the greatest stress in the base when b = 2 m.b) Find the width b so that there is a shrinkage zone at the base.(Note: unit weight of brick wall ỿ = 24 kN / m3 ) Answer: ϭmax=0,30 Mpa, b=2,23 m
Determine the active and passive force acting on a 3 meter high wall that supports clay with an undrained shear strength of 100 kPa and a unit weight of 19.20 kN/m
3. Compute the resultant lateral force for the soil-wall system shown in Figure 3. You may ignore tensile cracks. Use • A- Coloumb • B - Rankine 0=30°, y=20kN/m³ 4m Ground water table 7m c=50KN/m², p=10°, y=18KN/m³ 0=25°, y=20KN/m³ 8 m Gravity wall Figure 3
The following figure shows a section of an anchored retaining wall embedded into a saturated stiff clay layer. The sand has a unit weight of = 18 kN/m³, c' = 0 kPa and o' = 34º. The clay has a unit weight of = 20 kN/m³, c₁ = 80 kPa and = 0°. A uniform pressure of 40 kPa is applied on the soil surface. The short term stability of the wall is considered in an undrained analysis. Use the Rankin's theory of lateral earth pressure to determine the active and passive horizontal stresses. You should apply the requirements of AS 4678 and the partial factors of safety method in estimation of soil pressures. Assume the soil is in-situ and use a structural classification factor of ₁ = 1. 3m 1m Water table 1.5m 40 kPa Not to Scale Sand Clay Ta
A retaining wall supports a horizontal backfill that is composed of two types of soil. First layer: 4.84 meters high, Unit weight of 17.36 kN/m3, coefficient of active pressure of 0.285 Second layer: 5.68 meters high, Unit weight of 18.9 kN/m3, coefficient of active pressure of 0.307 Determine the distance of the total active force measured from the bottom of the wall. Round off t
Assume a smooth retaining wall as shown below. Calculate the hydrostatic force acting on the right side of the wall in kN per unit length (considering a 1 m length in the out-of-plane direction). The soil properties shown in the figure apply to either side of the wall g = 9.81m/s2
Q: For the retaining wall shown in the following figure, determine the force per unit length of the wall for Rankine's active state. Also find the location of the resultant. 3 m z 3 m y = 16 kN/m³ ' = 30° c' = 0 Groundwater table Y sat = 18 kN/m³ ' = 35° c' = 0
Find the passive earth pressure coefficient. For a vertical retaining wall having a backfill of dry sand inclined at an angle of 20° from the horizontal