A vertical retaining wall 8.8 meters high retains a horizontal backfill having the following properties: Void ratio = 0.64; Specific Gracvity = 2.64; Water Content = 28 %; Angle of internal Friction = 31°. Compute the location of the active force in meters from the bottom of the wall acting on it if the water table is 3.0 meters below the ground surface.

A vertical retaining wall 8.8 meters high retains a horizontal backfill having the following properties: Void ratio = 0.64; Specific Gracvity = 2.64; Water Content = 28 %; Angle of internal Friction = 31°. Compute the location of the active force in meters from the bottom of the wall acting on it if the water table is 3.0 meters below the ground surface.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Which of the two walls in Figure below gives the larger horizontal force? (Show calculations.)
A retaining wall with a smooth vertical back retains silt backfill for a depth of 6 m. The backfill has a horizontal surface having following properties c'= 10 kPa, = 20° and y = 17 kN/m³. Calculate the percentage decrement in the magnitude of thrust on the wall when the wall is restrained against yielding to when the wall is free to yield (assume development of tension crack when wall yields). A 32.8% B 45.7% C 50.3% D 61.4%
When movement of a wall under the earth pressures from the backfill was prevented the coefficient of earth pressure was recorded as 0.5. The ratio of the coefficient of passive and active earth pressure of the backfill is
Hand written and clean writing please
Given: → 4.5-m high retaining wall . Retaining homogeneous satorated soft clay. O'sat= 19.6 kNĪm³ Cu = 19.3 kN/m² ( undrained shear strergth) -> Diagram: Sopt Clay sat - 19.6 kN/m? Cu- 19.3 kN/m³ 4.5-m Make the necessary calu lation and draw the varialion of Rankine's active pressure on the wall with depth. nclude #te pressure from a waker-filled crack in - Find the depth up to which a tensile crack can occur. Delermink the total active force per unit lengh of the wall bepore the tensile crack gccurs. Assome tension stresses exist ard do not include the force from waler - filled Crack. - Delermine the tolal active force force per wall after the tensile crack occurs. 'Also, find Hhe locathon of the resultant. Neglect tersion shresses and include the force from the wafer-pilled crack. Find: your drawings unit lergth op the
At-rest: A 17-ft-high basement wall retains a backfill with y = 95 pcf, o' = 33°, c' 0 and OCR = 1.8. (a) Calculate the magnitude of the lateral thrust acting per unit length of wall: (b) Estimate the location of the lateral thrust measured from the bottom of the wall; and (c) Calculate the equivalent fluid pressure for this problem (Ans. 60 pcf). (Problem 13.2, Das and Sobhan, 2014).
A gravity retaining wall retains 12 m of a backfill, y = 17.7 kN/m² = 25° with a uniform horizontal surface. Assume the wall interface to be vertical, determine the magni tude and point of application of the total active pressure. If the water table is a height of 6 m. how far do the magnitude and the point of application of active pressure changed? Please solve carefully and don't give wrong answers and box the final answers
Consider the given retaining wall with backfill. The active earth pressure at base of wall is kN/m2. (upto two decimal places) 2m 5m 1m Į II (III) G=2.65 e = 0.85 = 0.08 w = 15° c=15 kN/m² G=2.7 c=0.8 $=10° c=20 kN/m² G=2.7 e=0.6 $ = 20° c=12 kN/m² A
The following figure shows a section of an anchored retaining wall embedded into a saturated stiff clay layer. The sand has a unit weight of = 18 kN/m³, c' = 0 kPa and o' = 34º. The clay has a unit weight of = 20 kN/m³, c₁ = 80 kPa and = 0°. A uniform pressure of 40 kPa is applied on the soil surface. The short term stability of the wall is considered in an undrained analysis. Use the Rankin's theory of lateral earth pressure to determine the active and passive horizontal stresses. You should apply the requirements of AS 4678 and the partial factors of safety method in estimation of soil pressures. Assume the soil is in-situ and use a structural classification factor of ₁ = 1. 3m 1m Water table 1.5m 40 kPa Not to Scale Sand Clay Ta
Determine the magnitude (kN) and location (m) of the resultant passive force on the 30m long wall.
(4) The backfill behind a retaining wall is clay with a unit weight of 18 kN/m', cohesion of 15 kPa, and an internal friction angle of 30°. The height of the wall is 6 m. The back of the wall is vertical and smooth, and the surface of the backfill is horizontal. Please calculate the active earth pressure on the wall back, including its distribution, the resultant force and its position.
Q-1: Figure-1 shows a 4.5-m-high retaining wall. The wall is restrained from yielding. Then find, the following conditions: A) Completely dry soil (no ground water) B) Completely saturated soil system