A 411-V long shunt flat-compound generator delivers 28 KW to a load. The armature resistance is 0.477 ohms, the shunt field resistance is 76 ohms, the commutating field winding resistance is 0.35 ohms, series field resistance is 0.338 ohms, and diverter resistance of 0.498 ohms. If the iron and friction losses are 601 watts, determine the commercial efficiency of the generator. Draw the equivalent circuit of the generator and the corresponding values of the components. Determine the following: a) eletrical b) mechanical and c) commercial efficiency Note: Write the equivalent numerical value of the commercial efficiency (percentage) of the generator in the given space below. The other required values will be verified in your submitted solution.

A 411-V long shunt flat-compound generator delivers 28 KW to a load. The armature resistance is 0.477 ohms, the shunt field resistance is 76 ohms, the commutating field winding resistance is 0.35 ohms, series field resistance is 0.338 ohms, and diverter resistance of 0.498 ohms. If the iron and friction losses are 601 watts, determine the commercial efficiency of the generator. Draw the equivalent circuit of the generator and the corresponding values of the components. Determine the following: a) eletrical b) mechanical and c) commercial efficiency Note: Write the equivalent numerical value of the commercial efficiency (percentage) of the generator in the given space below. The other required values will be verified in your submitted solution.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A shunt DC generator has no load terminal voltage of 140V. Armature resistance is 1ohm and shunt field resistance is 50ohm. Calculate the induced voltage.
I need the answer quickly
1A. Which of the following is/are a method of providing field excitation for a DC generator. a) separately excited shunt b) self-excited series c) self-excited shunt d) all of the above 1B. Which type of field winding typically has the higher resistance? a) series b) shunt
Draw the phasor diagrams for the following values of the power coefficient, ignoring the armature winding resistance of a 3-phase, star- connected, dislocated-pole synchronous generator. a) 0.8 inductive b)0.8 capacitive c) 1 omic
50 KW, 240 V enduvi resistance of a generator with foreign excitation is 0.02 ohms. Generatorproduces rated voltage at rated load. Endüvi voltage and endüvi current at rated loadcalculate? If the output voltage is kept constant at 240V and the output power is reduced to 45 KWfind the enduvi tension necessary for this?
Draw a developed diagram of a simple 2-layer lap-winding for a 4-pole generator with 8 coils.
Indui circuit resistance of 18 kW, 240V direct current series generator 0.12 Ohm, excitation winding resistance 0.08 is Ohm. Find the value of the moment induced in the inductor in this generator operating at 700 rpm at half load.
7) The flux per pole of a four-pole generator is 0.05 wb. It driven at a speed of 1500 rpm. In order to have an induced emf of 20 v per conductor, , if the winding is lap-connected, find (a) the number of conductors in series in each parallel path, (b) the number of conductors between brushes to generate 240 v, and (c) the total number of conductors in the armature.
D2. When a generator's full-load output voltage is the same as its no-load output voltage it is said to be a) under-compounded b) flat-compounded c) over-compounded d) none of the above D3. The output of an overcompounded DC generator can be lowered by use of a a) rheostat connected in series with the series field b) rheostat connected in parallel with the series field c) rheostat connected in parallel with the shunt field d) none of the above D4. When might it be desirable to use an overcompounded generator? a) never b) always c) to compensate for line loss d) when you need a higher no-load voltage than your full-load voltage