A 40-kVA, 8000/230-V distribution transformer has an impedance referred to the primary of 16 + j120 0. The components of the excitation branch referred to the primary side are Rc = 150 k) and Xc = 20 ka. If the primary voltage is 8150 V and the load impedance is ZL = 0.5 - j*2.7 Q what is the secondary voltage?

A 40-kVA, 8000/230-V distribution transformer has an impedance referred to the primary of 16 + j120 0. The components of the excitation branch referred to the primary side are Rc = 150 k) and Xc = 20 ka. If the primary voltage is 8150 V and the load impedance is ZL = 0.5 - j*2.7 Q what is the secondary voltage?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given Zo = -j324 N, R₁ = 436 N, Zc R₁ = 10754 N and a = 0.11, what RL is the magnitude of the source voltage Vs (in V rms) in the primary of the ideal transformer? Vs R₁ Answer: Zc Zc RL VL=28020 Vrms Use up to 2 digits after the decimal point if necessary in your answer below.
A multitap transformer has 1500 turns on the primary, 100 turns between B and C, 600 turns between A and D, and 500 turns between A and C. Calculate the secondary voltage between A and B if a 240V RMS source is connected to the primary. OB O A 134V RMS O 240V RMS O 96V RMS O 64V RMS
Transformers
2
Given three phase fullwave with center tapped transformer with 220 Vac source voltage, determine: Vdc, Vrms, Pdc, RF, and efficiency. D1 L1 D2 L1 L7 D3 220 Vac, 60 Hz Vo D4 RL=10 ohms L2 D5 L3 D6 m. L6 3 F12 87
Approximate solution time is 5 minutes. A transformer supplies power to a feeder that has five customers. Daily maximum demands for these customers are 120 kW, 40 kW, 90 kW, 110 kW, and 180kW. The maximum demand on the feeder is 243kW. The coincident factor of the feeder is
The parameters of a 500/1000V 50Hz single phase transformer are given below: Z₁ 1.2 +j2.40, Z₂= 2.3 + j6.5 N, R=100 , X-500 N and Z₁= 23 +j20 N. If the primary current and power factor are: 45A and 0.67 lagging, at nominal input voltage. By using the exact equivalent circuit, find the required additional capacitor in parallel with load to correct the input power factor to unity power factor at the same current.
An ideal transformer is connected to a 110V(rms), 60HZ source. Line impedance on the primary is 4+5i2 and on the secondary side is 1+2i2. A lmF capacitor is connected as load on the secondary side. Transformer has 100 turns on the primary side and 50 turns on the secondary side. Calculate: (i) Primary and secondary current (ii) Active and reactive power supplied by the source. (iii)Power factor of the source.
A transformer has a rated output of 400 kVA at a power factor of 0.6. Determine the rated power output and the corresponding reactive power.
Give corect answer
A transformer has a rated output of 400 kVA at a power factor of 0.6. Determine the rated power output and the corresponding reactive power.
i need the answer quickly