A 15-kVA 8000/230-V distribution transformer has an impedance referred to the primaryof 80 + j3000. The components of the excitation branch referred to the primary side areRC = 350 kn and XM = 70 k. (a) If the primary voltage is 7967 V and the loadimpedance is ZL = 3.0 +j1.5 №, what is the secondary voltage of the transformer? What isthe voltage regulation of the transformer? (b) If the load is disconnected and a capacitorof-j4.0 2 is connected in its place, what is the secondary voltage of the transformer?What is its voltage regulation under these conditions?

a. The turns ratio of the transformer is determined as a=8000230=34.78 The load impedance referred…

A 15-kVA 8000/230-V distribution transformer has an impedance referred to the prima of 80+ j3000. The components of the excitation branch referred to the primary side ar RC = 350 kN and XM = 70 kQ2. (a) If the primary voltage is 7967 V and the load impedance is ZL = 3.0 +j1.5 2, what is the secondary voltage of the transformer? Wha the voltage regulation of the transformer? (b) If the load is disconnected and a capacito of-j4.0 N is connected in its place, what is the secondary voltage of the transformer?

A 15-kVA 8000/230-V distribution transformer has an impedance referred to the prima of 80+ j3000. The components of the excitation branch referred to the primary side ar RC = 350 kN and XM = 70 kQ2. (a) If the primary voltage is 7967 V and the load impedance is ZL = 3.0 +j1.5 2, what is the secondary voltage of the transformer? Wha the voltage regulation of the transformer? (b) If the load is disconnected and a capacito of-j4.0 N is connected in its place, what is the secondary voltage of the transformer?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the scheme of a single-phase transformer with two secondary windings and mark the main symbols and quantities. Write the formulas to determine the total power P1, the transformation ratios and the primary current I1.
A 40-kVA, 8000/230-V distribution transformer has an impedance referred to the primary of 16 + j120 0. The components of the excitation branch referred to the primary side are Rc = 150 kQ and Xc = 20 ka. If the primary voltage is 8150 V and the load impedance is ZL = 0.5 - j*2.72 what is the secondary voltage?
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:14 and a no-load primary voltage of 17 (line-to-line) kV. The step- down transformer has a turn ratio of 18:1 and it has a Y-connected, balanced load of 0.463 +j 0.0772 ohms connected to its secondary side. A capacitor bank of -j0.324 ohms is added parallel to the load. Assuming an ideal transmission line, the effective impedance (per phase) of the system seen by the source would be: O A. 0.292 + j0.375 O B. None of the other choices are correct O C. 0.584 + j0.750 O D.0.196 + j0.158 O E. 5.84 + j7.5
3. A non-ideal 1-phase transformer has turns ratio 5:1 with 120Vac primary. The primary impedance is 1 + j1 Ohms, and the secondary impedance is 0.2 + j0.2 Ohms. Assume the core impedance (R0 and X0) can be neglected. A resistive load of 12 Ohms is connected to the secondary. What is the primary current magnitude? What is the secondary voltage magnitude? What is the efficiency of this transformer with this load?
Explaination please...Thank you for your help! A 40 kVA 6000/240-V distribution transformer has an impedance referred to the primary of 15+j80Ω. The components of the excitation branch referred to the primary side are RC = 80 kΩ and XM =25 kΩ. The primary voltage is 5975 V and the load impedance is 2.2 + j0.8 Ω. What is the voltageregulation of the transformer?
How does the coupling factor affect the primary and secondary voltages? For example if the turns ratio in my transformer is 1:2 and the Vin is 10V, the voltage on the primary side is 10V and the voltage on the secondary side is 20V when the coupling factor (k) is 1. What will the primary and secondary voltages be if the coupling factor becomes 0.5?
When the transformer is loaded in a balanced fashion up to its nominal rating (10 MVA), calculate the high side line-to-line phasor voltages (ab, bc, ca). and low side phasor voltages both line-to-line and line-to-neutral (ab, bc, ca, a, b,c). as a reference for calculations the low side A line to neutral voltage is 7620V at an angle of 0 degrees when the transformer is at rated power. The transformer has the following characteristics: V: 138kV delta high side/ 13.2 kV wye low side 9% impedance X/R ratio of 20
a single-phase transformer serves a 7.2kw resistive loadlocated 200 ft from the transformer. each conductor from the transformer to load has an impedence of (0.78+j0.052) ohms per 1000ft. if the voltage at the load terminal is 240v, the magnitude of the voltage (v) at the transformer secondary is most nearly:
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) kV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +j 0.0816 ohms connected to its secondary side. A capacitor bank of -j0.171 ohms is added parallel to the load. Assuming an ideal transmission line, the load voltage (line-to-neutral) would be: O A. 7360 V O B. 6.2 kV O C. 12750 V O D. 4806 V O E. None of the other choices are correct
In a transformer that has 10 times more turns on the secondary side (side 2) than on the primary side (side 1), the magnitude of the voltage/EMF across the windings on the secondary side, E₂ will be... O a.... 10 times lower than the voltage/emf on the primary side, E₁. O b.... the same as the voltage/emf on the primary side. O c.... always zero regardless of the voltage on the primary side, E₁. O d.... 10 times higher than the voltage/emf on the primary side, E₁.