A 38.1 mm pulley is fastened to a 120 mm shaft by means of square key with 150 mm long. Whatforce tangent to pulley rim will crush and key if bearing stress is 410 Mpa? Assume key and shaft are ofthe same material.

A sheave or tiny wheel with a grooved rim and with or without the block in which it travels is used…

Answered: A 38.1 mm pulley is fastened to a 120…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please don't provide handwrittenh solution.
I need the answer as soon as possible
A shaft has a diameter of 45.08 mm and is an interference fit with a sleeve 60 mm outer, 45 mm inner 45 mm inner diameters and 80 mm long. Calculate: i. The force needed to slide the sleeve on the shaft, and ii. the change in radius of the shaft and sleeve at the inside. Assume the elastic properties for both are the same with Young's modulus of elasticity as 200 GPa and Poisson's ratio of 0.3.
(b)Find the torque required to raise the load of 15kN and mean diameter of triple threaded screw being 46mm. Also gIven pitch = 8mm and coefficient of friction is 0.15?
A pulley is keyed to a 28 mm steel shaft with a 7 mm x 8 mm x 20 mm key. If the hub length is 20 mm and the allowable crushing stress for the key material is 105 MPa, How much torque can be transmitted in kN-m?
Problem parameters for Case #2: Cases Load (lbs) 2 55,000 What is the total Deformation in (in) on the rod? Note: • Give your answer rounded to 3 decimal place i.e. 0.04352 = 0.044 or 0.04342 = 0.043 • Do NOT include any units or other text. The size of your numeric value should be given in (in). i.e. if your answer is 0.043 (in) then enter this as "0.043" (Do NOT enter "0.043 in")
A hollow steel shaft is to transmit 4,867 N-m of torque and is to be sized so that the torsional stress does not exceed 176 MPa. If the inside diameter is three-fourths of the outside diameter, what is the exact outside diameter size of the shaft in mm?
mechanical design
Design the rectangular key which is located on the shaft motor if the diameter of it Is ( 48 ) mom and shearing and crushing stresses which applied of it are ( 420 ) Nimm and ( 700 ) N / mm' respectively , when the force applied on the key equal to ( 8 000 ) N ? jo 5:18 /
A square key fixing a gear on a 30 mm diameter shaft. The shaft is transmitting a power of 18 kW to the gear at 800 rpm. The key is made of steel with a yield strength of 470 N/mm² and the factor of safety is 2.5. The yield strength of the key material in compression can be assumed to be equal to the yield strength in tension. Determine the dimensions of the key.

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A 38.1 mm pulley is fastened to a 120 mm shaft by means of square key with 150 mm long. What force tangent to pulley rim will crush and key if bearing stress is 410 Mpa? Assume key and shaft are of the same material.