Design a flanged coupling that will be able to carry power of1,500 HP using a factor of safety of 3.3 at 630 rpm. The shaftdiameters of the equipment the coupling will connect are both 5inches. Check your design for the following stresses if N = 3.3 issatisfied: 1. Bolt shearing; 2. Bolt bearing; 3. Shearing of hub fromcoupling flange; 4. Shear on key; 5. Compression on key; Selectdimensions whichever is higher. 6. Calculate also minimum lengthof engagement of the bolt and nut if these are of the same material.5 inch dia.shaftscoupling to connect theequipment shafts. Note: use4 bolts onlyInstructions:

Answered: Image /qna-images/answer/a614a131-9fd7-4914-8107-ae6211304a32.jpg

Answered: 5 inch dia. shafts coupling to connect…

Engineering

Mechanical Engineering

5 inch dia. shafts coupling to connect the equipment shafts. Note: use 4 bolts only nstructions:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Design a rigid flange coupling to transmit a torque of 228N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa > Provide FBD
A mild steel shaft has to transmit 75 kW at 200 rpm. Design a cast Iron flange coupling for the shaft. The allowable stresses are Shear stress for the shaft and keys 40 N/mm²Shear stress for bolts = 28 N/mm²Shear stress for C.I. coupling = 20 N/mm² Take wearing stress as twice the shear stress value and number of bolts for coupling as 6.
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete handwritten solution
Design a typical rigid flange coupling for connecting a motor and a centrifugal pump shafts. The coupling needs to transmit 15 KW at 1000 rpm. The allowable shear stresses of the shaft, key and bolt materials are 60 MPa, 50 MPa and 25 MPa respectively. The shear modulus of the shaft material may be taken as 84GPa. The angle of twist of the shaft should be limited to 1 degree in 20 times the shaft diameter. Note: show complete solution
. The mean diameter of the driving pulley for a vec-belt drive with two belts is 110 mm. The pulley groove angle is 40° and the drive transmits 4.4 kW at a speed of rotation of 1500 rev/min. The coefficient of frietion between belt and pulley 0.32, and the angle of lap is 160°. Determine the driving torque and the maximum stress in the belt material if the cross-sectional area of each belt is 120 mm.
Design and draw a neat sketch of a cast iron protective type flange coupling to transmit “P” kW at “N” rpm. from a turbine generating n electric motor to a compressor. The service factor may be assumed as 1.35. The following permissible stress may be used: Shear stress for shaft, bolt and key material = 40 MPaCrushing stress for bolt and key = 80 MPaShear stress for cast iron = 8 Mpa Speed N in Rpm = 200Power P in kN = 16
5. Design a sleeve coupling for the transmission of 12 kW at 300 rpm by two connected steel shafts. Take service factor KS 1.25. The sleeve is made of CI. The key and the shaft are made of the same material. Allowable stress: Shear stresses in key and shaft 50 MPa Crushing stress in key= 100 MPa Shear stress in CI sleeve = 10 MPa
1.
(4) An electric motor purchased by your employer surprisingly arrived without a keyway in the shaft. The motor has power rating of 7.5kW & 1,800rpm & has a shaft of Ø17mm. It will be used to drive a centrifugal pump using cast iron sheave. Design the square key to be used in the assembly based on maximum bearing & shearing stresses of 580MPa & 370MPa, respectively, and factor of safety of 5.
Torque =230 N-m
Figure below shows a portion of a pump that is gear-driven at uniform load and speed. The 25 mm diameter solod shaft supported by the bearings is to be made of machined AISI 1045 CD steel. The helical gear is subjected to the axial force F =499 y a radial load F = 741 N and a tangential load of F=2,006 N. Assume the component is operating at room temperature of 70°F and the material has 50% reliability factor. 25-mm solid Bending K, = 2.0 round shaft Fillet Torsional K = 1.5 F. F, Axial K, = 1.8 F Pump Helical spur gear 50 mm -250-mm dia.- FIGURE 1. Identify the critical location(s) of stress and show it clearly in a diagram. 2. Identify cleary, all the components of stresses (at the critical point) that will be calculated (by drawing and clearly showing the XYZ axes) and show it in a matrix form. Show which components of stresses will have a value zero or non-zero. 3. Calculate the principal stresses and principal directions. Show the principal stresses clearly in a stress element…
A brass spur rotating at 600rpm drives a cast iron spur gear at a transmission ratio of 4:1.the allowable static stresses for the spur pinion and cast iron gear are 84MPa and 105MPa respectively.the pinion has 16 standards 20 degrees full depth involute teeth of module 8mm.the face width of both the gear and the pinion is 90mm. From the stand point of strength, calculate; (A) tangential load on the tooth (B) power transmitted