A 325mmx475mm (bxh) 7.75m simple beam carries a total dead load of 22KN/m and a live load of33KN/m. Clear cover is 40mm, diameter of shear reinforcement to be 10mm, concrete strengtn to be28MPA, steel strength for transverse reinforcement to be 420MPA and reinforced with 4D28mm rebar 1layer.Determine the balanced steel area in mm2.Your answerDetermine the maximum steel area using a steel strain of 0.004, mm2.Your answerDetermine the maximum moment using a steel strain of 0.005, kN-m.Your answerDetermine the design strength in kN-m.Your answer

NOTE: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

A 325mmx475mm (bxh) 7.75m simple beam carries a total dead load of 22kN/m and a live load of 33KN/m. Clear cover is 40mm, diameter of shear reinforcement to be 10mm, concrete strength to be 28MPA, steel strength for transverse reinforcement to be 420MPa and reinforced with 4028mm rebar 1 layer. Determine the balanced steel area in mm2. Your answer Determine the maximum steel area using a steel strain of 0.004, mm2. Your answer Determine the maximum moment using a steel strain of 0.005, kN-m. Your answer Determine the design strength in kN-m. Your answer

A 325mmx475mm (bxh) 7.75m simple beam carries a total dead load of 22kN/m and a live load of 33KN/m. Clear cover is 40mm, diameter of shear reinforcement to be 10mm, concrete strength to be 28MPA, steel strength for transverse reinforcement to be 420MPa and reinforced with 4028mm rebar 1 layer. Determine the balanced steel area in mm2. Your answer Determine the maximum steel area using a steel strain of 0.004, mm2. Your answer Determine the maximum moment using a steel strain of 0.005, kN-m. Your answer Determine the design strength in kN-m. Your answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

IF YOU DO NOT WANT TO ANSWER MY QUESTION, DO NOT REJECTED IT. SOMEONE ELSE WILL SOLVE IT I did not pay the subscription amount in order for my questions to be rejected!!!
A beam cross-section is limited to the size shown. Determine the required area of reinforcement for service load moments Mp = 400 ft-kips and ML = 250 ft-kips. Check crack control requirements f = 4000 psi (normalweight) f, = 60,000 psi d' = 2.5" b= 12" A's d₁= 32"
a two span beam subject to shear and flexure only is reinforced as follows: Section: TOP BARS @ midspan: 2-ø20mm @ face of supports: 5-ø20mm Section: BOTTOM BARS @midspan: 3-ø20mm @ face of supports: 2-ø20mm GIVEN: Stirrup diameter ds = 10mm concrete f'c= 21 mpa steel rebar fy= 415 mpa stirrup fy = 275 mpa beam size b x h = 270 mm x 450 mm assume all bars laid out in a single layer. Determine the DESIGN moment strength of section at midspan for positive bending
Do not use chatgpt and pls don't provide image solution otherwise I will downvote you
Please give explanations with formulas and referencing the diagram where possible
In the design of beam for the limit state of collapse in flexure as per IS 456 : 2000, let the maximum strain in concrete be limited to 0.0030 (in place of 0.0035) for this situation consider a rectangular beam section of width 300 mm, effective depth as 400 mm, area of tension steel used is 900 mm2. Material used is M20 concrete mix Fe415 grade steel (a) Limiting depth of neutral axis (b) Actual depth of neutral axis
7. For a beam of cross-section, width = 230 mm and effective depth = 500 mm, the number of rebars of 12 mm diameter required to satisfy minimum tension reinforcement requirement specified by IS: 456-2000 (assuming grade of steel reinforcement as Fe500) is mi
( CECE2240 - Design of structure -1 ) EXPERIMENT :Designing and detailing of singly reinforced simply supported beam - ACI Code Step 1 Step 2 Step 3 Step 4
Please solve fast, its urgent