A 300 mm X 500 mm exterior beam is reinforced with 25 mm main bars and 12 mm stirrups. The tension side has a steel area of 2450 mm² and the compression side has a steel area of 1480 mm². 60% of the tension steel area is laid out on the first layer, the remaining is on the second layer and the compression steels are on a single layer. Determine the following if the steel yield strength of the compression steel is 276 MPa, the steel yield strength of the tension steel is 415 MPa and the depth of the tension zone 340 mm: a. The compressive stress in the concrete.

A 300 mm X 500 mm exterior beam is reinforced with 25 mm main bars and 12 mm stirrups. The tension side has a steel area of 2450 mm² and the compression side has a steel area of 1480 mm². 60% of the tension steel area is laid out on the first layer, the remaining is on the second layer and the compression steels are on a single layer. Determine the following if the steel yield strength of the compression steel is 276 MPa, the steel yield strength of the tension steel is 415 MPa and the depth of the tension zone 340 mm: a. The compressive stress in the concrete.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

FN= 119 mPa, SN= 93MPa. provide fbd
A composite bar is made of Steel & Aluminium strips each having 3 cm² area of cross-section. The composite bar is subjected to an axial load of 12000 N. If Esteel = 3EÃ¡, the stress in steel is
An unstiffened web I-section fabricated from a 10 mm thick plate by fillet welding as shown in the figure. If yield stress of steel is 250 MPa, the maximum shear load that section can is take is [2 Marks] 10 mm 300 mm 10 mm 200 mm
5. A bronze bar is fastened between a steel bar and an aluminum bar as shown in Figure 5. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m FIGURE 5 Aluminum A = 320 mm² 1.5 m 2P
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 25 kips, w = 3.6 kips/ft, LAB = 5.6 ft, LBC = 5.6 ft, and LcD = 16.8 ft. Determine the magnitude of the maximum bending stress in the beam. LAB Answer: Omax = i B LBC C ksi W LCD D ZOQ Q 214% TOP BARI ENG 11:41 am 35 28/04/2023 8 cores
Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
Concrete has no tensile strength. True False
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
Sketch a sample stress-strain behavior of steel and identify different levels of strength.
The light rigid bar ABCD shown is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. %3D Steel E200 GPa A-600mm L1 m 2.0 m 0.6 m 1.5 m Pa20 KN Aluminum E-70 GPa A=900mm L-1.5 m What is the ratio of the deformation of steel to deformation of aluminum?