A 30-mm--dia.-bar was subjected to a tensile load of 54 kN and a measured extension on a 300 mm gauge length was 0.112 mm and change in diameter was 0.0366. Compute the shear modulus of rigidity in GPa. * 77.20 204.60 196.00 112.40 166.80 Compute the young's modulus of elasticity in GPa. * O 77.20 204.60 196.00 112.40 166.80

A 30-mm--dia.-bar was subjected to a tensile load of 54 kN and a measured extension on a 300 mm gauge length was 0.112 mm and change in diameter was 0.0366. Compute the shear modulus of rigidity in GPa. * 77.20 204.60 196.00 112.40 166.80 Compute the young's modulus of elasticity in GPa. * O 77.20 204.60 196.00 112.40 166.80

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer and round off only in two decimals in the final anwer
Read the question carefully and give me solution according to the question. Urgent please
Solve 2 part A and B please
With the dimensions already given, determine the allowable value of the tensile load P, considering the following parameters (The figure shown below is a hanger): 1. The allowable normal stress at the two vertical bolts (bolts 1 and 2) is 160 MPa. 2. The allowable tensile stress in the hanger (see label) is 110 MPa. 3. The allowable tensile stess in the hanger considering the cross section through the horizontal bolt is 75 MPa. 4. The allowable shear stess at the horizontal bolt is 45 MPa. 5. The allowable bearing stress between the washer and the clip angle at the vertical bolts is 65 MPa. 6. The allowable bearing stress at the "shank" of the horizontal bolt is 180 MPa. 7. The allowable shear stress through the clip angle at the vertical bolts is 35 MPa. Note: Draw the Free Body Diagram, include the proper units and round-off the answers to 3 decimal places.
S = Area of Bearing (in²) 4 4 4 +Tabulated Data and Result Specimen No. 1 2 3 Maximum Load Area of Bearing Maximum Load (lbs.) 20000 20500 21000 Compressive Strength (psi)
(b) The tress at elastic limit (c) The percentage elongation (d) The percentage decreases in area
Subject: Steel design- Bolted Steel Connection - Bolted Subjected to Eccentric Loads *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten
7. ASTM suggests a tolerance of... percent to allow the variation in strength as a test of ....w. water. A. 12 В. 8 C. 10 D. 15 E. 16 F. None of them
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
(in %, up to two decimal places) is. outer diameters of 100 mm and 106 mm. respectively. The area ratio of the core cutter A core cutter of 130 mm height has inner and Set-
I need only handwritten And correct
Five plates with thickness t are bolted together by a bolt with diameter d. Which of the following gives the maximum bearing stress among all the plates? A.1.50 P/bt B.1.50 P/nd2 0.75P- C.0.75 P/bt 1.5P D.0.750 P/id2 0.75P- For the deformed plate shown in figure X, the magnitude of the shear strain at point D is nearest to 2 mm 5 mm A.0.229 rad B.0.004 rad C.0.573 rad D.0.010 rad 500 mm 500 mm Plates A and B are to be connected using bolts and two cover plates C and D as shown. The force exerted on plate A is 30 kN and the diameter of the bolts used is 25 mm. The thickness of all the plates is 15 mm. Which of the following is the shear stress experienced by either bolt? A.30.6 MPa F B.61.1 MPa B C.45.8 MPa D.15.3 MPa B