A 3-phase star connected balanced load is supplied from a 3 phase, 408 V supply. The line current is 17 A and the power taken by the load is 7600 W. Find () impedance in each branch (i) power factor and (ii) power consumed if the same load is connected in delta. Impedance Power factor Power when connected in delta

A 3-phase star connected balanced load is supplied from a 3 phase, 408 V supply. The line current is 17 A and the power taken by the load is 7600 W. Find () impedance in each branch (i) power factor and (ii) power consumed if the same load is connected in delta. Impedance Power factor Power when connected in delta

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a delta connected load Select one: O a. Phase and line currents are not equal O b. Phase current is zero Oc. Phase and line voltages are equal O d. Phase and line voltages are not equal
A balanced load is connected in star across a 3 phasec415V 50Hz supply. The load consists of a coil of resistance 25 ohms and inducrance 0.5 henry in paeallel with a purw resistance of 28 ohms and a pure capaciror of 60microfarads capacitance ,in each branch. Calculate a. The line currents The answer has to be 9.3A
Q- A 30 KVA, 2500/230 transformers has leakage impedance of 8%. Find the voltage to be applied on hV side to circulate full load current with low voltage winding shorted.
A delta connected load (Figure 2) has an impedance Z is(12 + j35) ohms. If the applied VAB voltage is 380 V with -50º phase . Get the current IC and load IAB current.
A three-phase alternator generating unbalanced voltages is connected to an unbalanced load through a 3-phase transmission line as shown in figure. The neutral of the alternator and the star point of the load are solidly grounded. The phase voltages of the alternator are Ea = 1020º, Eb = 102-90°, Ec = 10/120⁰ E E E The positive sequence component of the load current is (A) 1.3102-107⁰ A (B) 0.3322-120° A (C) 0.9962-120º A (D) 3.5104-81⁰ A +) + j1.002 0000 j1.002 0000 j1.0Ω vovo j1.0Ω 0000 j2.002 voor j3.002 oooo
In a 3-phase balanced star connected system, the least number of wattmeter essential to measure the power is
Three impedance Z1=20<30 ohm , Z2=15<-45 ohm and Z3=10<0 ohm are connected in parallel with a voltage source V= 100 <-45 volt .Find the power triangle of each branch then combine them together to obtain the total power triangle
A 440 V, 60 Hz generatorsuppliestwo parallel-connected loads A and B,. LoadA draws an apparent power of 100 KVA at 0.8 pf lagging and load B draws anapparent power of 70 KVA at unity pf. Determine the KVA supplied by the generator.
Q- A 30 KVA, 2500/230 transformers has leakage impedance of 8%. Find the voltage to be applied on hV side to circulate full load current with low voltage winding shorted.
Solve it please fast
2. For the following system shown in the figure, calculate: a. The current through each phase of the load. b. The total real and reactive power of the three-phase load. c. The power factor at the load side. A 220 V 20° 220VL-120° U8 vol 152 I 220 VI20° 9. M.
Q-3-) a V346.41 V b Z=0+339 Z=0+j3Q Z=0+/39 m Line V₂ R R R=1252 Star-Connected load R b-) Find the voltage drop value in the energy distribution line. c-) Find the voltage V₂ at the load ends at the end of the line. R B R R=1892 Delta-Connected load In the figure above, two balanced 3-phase delta and star-connected loads are connected in parallel to a balanced three-phase power distribution line. Delta and star connected loads are completely resistive and the resistance values per phase are 18 2 and 12 22, respectively. The phase-to-phase voltage value of the source feeding the line is 346.41 V (rms), and it is assumed that the three-phase network between the source and the load has an inductive reactance value of 3j 2 per phase. a-) Find the total current drawn from the source, active and reactive power values by selecting the Van voltage as a reference value.