A 3-phase, 4-pole, 230-V wound rotor induction motor (WRIM), has both its stator and rotor connected in wye. The rotor has half as many turns per phase as the stator. If the rotor is turning at 1725 rpm, determine: a. Slip in decimal and in per cent b. The blocked-rotor voltage per phase C. The rotor voltage per phase at the specified speed

A 3-phase, 4-pole, 230-V wound rotor induction motor (WRIM), has both its stator and rotor connected in wye. The rotor has half as many turns per phase as the stator. If the rotor is turning at 1725 rpm, determine: a. Slip in decimal and in per cent b. The blocked-rotor voltage per phase C. The rotor voltage per phase at the specified speed

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 6RQ: Name three factors that determine the torque produced by an induction motor.

See similar textbooks

Similar questions

6- Which of the following supply is given to the rotor winding of 3-Phase Induction Motor: a) DC Supply b) AC Supply c) No Supply d) Pulsating Supply 7- 3-Phase Induction Motor will have Starting Torque and Starting Current a) High, High b) Low, Low. c) High, Low d) Low, High 8- Which of the following method is used for controlling the speed of an induction motor: a) Changing number of stator poles b) Supply voltage control c) Frequency control d) All the options are correct 9- Which of the following method cannot be used for starting of 3-Phase Squirrel Induction Motor: a) Star-Delta Starting b) Line resistor startling c) transformer Starter d) Rotor Resistance Starting 10- The rotor of a stepper motor has no: a) windings b) commutator c) brushes d) all of the above
Here it is the equivalent circuit of and induction motor and it is per phase circuit my question is name for me the variable for example R1 is the winding resistance and so an the all variable and please show me a pic of the real machine with the variable for example for R1 happens because of the winding i need to see the winding in the real machine, please help me to understand well
8. A 3-phase induction motor is running at 2% slip. If the input to rotor is 1000 W, then mechanical power developed by the motor is ............ (i) 20 W (iii) 500 W (ii) 980 W (iv) 200 W
A 3-0, 50-Hz induction motor with its rotor star-connected gives 500 V (r.m.s.) at standstill between slip-rings on open circuit. Calculate the current and power factor in each phase of the rotor windings at standstill when joined to a star-connected circuit, each limb of which has a resistance of 10 Q and an inductance of 0.03 H. The resistance per phase of the rotor windings is 0.2 Q and inductance 0.03 H. Calculate also the current and power factor in each rotor phase when the rings are short- circuited and the motor is running with a slip of 4 per cent. [13.6 A, 0.48; 27.0 A, 0.47] (London University) A 4-pole, 50-Hz, 3-phase induction motor has a slip-ring rotor with a resistance and standstill reactance of 0.04 2 and 0.2 2 per phase respectively. Find the amount of resistance to be inserted in each rotor phase to obtain full-load torque at starting. What will be the approximate power factor in the rotor at this instant ? The slip at full-load is 3 per cent. [0.084 2, 0.516 p.f.]…
1. The operation of Commutator in DC Motor is * O a) to convert dc to ac O b) to convert ac to dc O c) to convert fixed dc to variable dc O reverse the current direction in the rotating windings each half turn
T-a. The direction of rotation of a single-phase split-phase motor can be change by........ a) reversing the connection of the start winding b) reversing the connection of the run winding c) reversing the connection of the start and run winding at the same time d) "a" or "b", not "c" T-b. Single-phase split-phase motors using an electrolytic capacitor in the start winding circuit should not be cycled more than about__________ time per hour. a) 8 b) 12 c) 24 d) none of the above T-c. When replacing the capacitor in a capacitor-start induction-run motor, one must be sure to replace the bad capacitor with__________ . a) a smaller one b) one of the same size c) a larger one d) none of the above
A four-pole induction motor drives a load at 2478 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Part A Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. Express your answer to three significant figures and include the appropriate units. f= Submit Part B Value I = HA Request Answer Submit If the dc-to-ac converter has a power efficiency of 90 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source. Express your answer to three significant figures and include the appropriate units. HÅ Value Units Request Answer ? Units ?
A four-pole, wave-wound generator has 220 coils of 10 turns each. The resistance of each turn is 0.02 2. Find the resistance of the armature winding.
A 3-phase, 50-Hz induction motor with its rotor star-connected gives 500-V(r.m.s.) at standstill between the slip-rings on open-circuit. Calculate the current and power factor at standstill when the rotor winding is joined to a star-connected external circuit, each phase of which has a resistance of 10 Q and an inductance of 0.04 H. The resistance per phase of the winding is 0.2 Q and its inductance is 0.04 H. Also, calculate the current and power factor when the slip-rings are short-circuited and the motor is running with a slip of 5 per cent. Assume flux remain constant.
A) Although the magnetic field for each phase of a 3-phase induction motor is merely switching back and forth between north and south poles, the resultant magnetic influence from all phases sets up a rotating magnetic field to cut the rotor conductors. a) true b) false B) In a two-pole stator winding of a 3-phase motor, how many revolutions does the rotating tr) magnetic field make in one cycle of the electrical current? a) one b) 60 c) 3600 d) none of the above
3-Phase 50Hz 6 pole induction motor has rotor resistance of 0.1 ohm and reactance of 0.92. ignore voltage drop in stator and assume thee rotor resistance is constant. Full load slip is 3%, then find Tmax /Tfl
I need the answer as soon as possible