QI) In a box there are 100 resistors having resistance and tolerance as shown in the following table. Let a resistor be selected from the box and assume each resistor has the same likelihood of being chosen. Define three events A as draw a 472 resistor, B as draw a resistor with 5% tolerance and C as draw a 1002 resistor. Find P (A/B), P (A/C).P (B/C). Resistznce a 10% Total 22 10 14 24 17 28 16 44 100 24 32 Tatal 62 38 100

QI) In a box there are 100 resistors having resistance and tolerance as shown in the following table. Let a resistor be selected from the box and assume each resistor has the same likelihood of being chosen. Define three events A as draw a 472 resistor, B as draw a resistor with 5% tolerance and C as draw a 1002 resistor. Find P (A/B), P (A/C).P (B/C). Resistznce a 10% Total 22 10 14 24 17 28 16 44 100 24 32 Tatal 62 38 100

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 3PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

If you wanted to measure the voltage of a resistor with a voltmeter, would you introduce the voltmeter to be in series or in parallel to that resistor? Explain. What about for an ammeter?
INSTRUCTION: Connect two resistors (R1 and R2 in parallel and then in series, then find the resistance. -Resistance of the resistors could not be measured on the UT33B multimeter, so the voltage and current were measured and the resistance was found using ohms law. RESISTOR 1 and 2 in series - Voltage across the series arrangement of resistors is measured to be 1.524 V, The scale used to measure voltage is 2000mV on the UT33B multimeter. - Current across the series arrangement of resistors is measured to be 0.04 A, The scale used to measure current is 10 A on the UT33B multimeter. RESISTOR 1 and 2 in a parallel - Voltage across the parallel arrangement of resistors is measured to be 1.568 V, The scale used to measure voltage is 2000mV on the UT33B multimeter. - Current across the parallel arrangement of resistors is measured to be 0.15 A, The scale used to measure current is 10 A on the UT33B multimeter. i) Compare the theoretical effective resistance using the nominal values in…
A resistance arrangement of 50 ohm is desired. Two resistors of 100.0 ± 0.1 ohm and two resistors of 25.0 ± 0.02 ohm are available. Which should be used to results in the lowest uncertainty, a series arrangement with the 25-ohm resistors or a parallel arrangement with the 100-ohm resistors? Calculate the uncertainty for each arrangement
Draw a schematic of a circuit that converts the thermistor resistance to a measurable voltage. I suggest basing it on the only circuit you have studied so far: the voltage divider. Assuming that you have a negative-thermal coecient (NTC) thermistor and that you want higher temperature to result in higher voltage, which of the resistors in a voltage divider is the thermistor and which is a fixed resistor? Use the proper thermistor symbol and put the thermistor part number on the schematic. (For the final report, update this schematic with the resistor value chosen in the lab.)
Two resistors must be selected so that the currentin one is four times the current in the other. If. their equivalent parallel resistance is 5k,calculate R 1and R2.(Ans: 6.25k , 25k
A secondary cell having an emf of 7V and an internal resistance of 2.5 is connected in series with a primary cell having an emf of 4V and an internal resistance of 45 the negative terminal of each cell being connected to the positive terminal of the other cell. A voltmeter having a resistance of 75 is connected to measure the terminal voltage of the cells. Calculate the voltmeter reading and the current in each cell.
Determine the resistor voltage. The source is 6V, Zener potential is 5.1V and resistor is 1k ohms.
Hello, I am very confused what is a hyrbrid pi model. Can you please make a hypbrid pi model from this circuit and explain thank you I will like
Resistors A, B, and C are in series with a 100-V source. The total voltage drop across A and B is 50 V, and that across B, and C, is 80 V. Find the three resistances if the total resistance is 50 ohms.
To measure the change in resistance of the gage(s) and indicate the location of the gauge on the beam, construct the Wheatstone bridge circuit. Calculate the Wheatstone bridge output if the gauge indicates a strain of 4000.then,Evaluate how can the number of strain gauges affects your measurement result. Justify your response with a calculation and a diagram showing the gage's placement on the beam.
Note: Answer must not be in terms of the unknown voltage Vs, and unknown current Is.
A secondary cell having an end of 2v and internal resistance of 1amp is connected on series with a primary cell having an end of 1.5v and internal resistance of 100amp, the negative terminal of each cell being connected to the positive terminal of the other cell . A voltmeter having a resistance of 50amp is connected to measure the terminal voltage of the cells. Calculate the voltmeter reading and the current in each cell.