A 3-phase, 200-hp, 3300-V, star-connected induction motor has the following equivalent circuit parameters per phase: RI - R2 =0.8 ohm; x/-x'2-3.5 ohm Calculate the slip at full load if the friction and windage loss is 3 kW. How much extra rotor resistance would be necessary to increase the slip to three times this value with the full-load torque maintained? How much extra stator resistance would be necessary to achieve the same object and what loss of peak torque would result?

A 3-phase, 200-hp, 3300-V, star-connected induction motor has the following equivalent circuit parameters per phase: RI - R2 =0.8 ohm; x/-x'2-3.5 ohm Calculate the slip at full load if the friction and windage loss is 3 kW. How much extra rotor resistance would be necessary to increase the slip to three times this value with the full-load torque maintained? How much extra stator resistance would be necessary to achieve the same object and what loss of peak torque would result?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Question.
Complete solution otherwise skip. Plxxx.
What is ampere circuital law?
I need the answer as soon as possible
Question Completion Status: Click Submit to complete this assessment. Question 8 What do you do to an asynchronous counter to let it count froms14 to 0? (Handwriting solution is needed: include this in your pdf file) Click Submit to complete this asseESment,
We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation. A #6 AWG B 600 Kcmil C #8 AWG D #2 AWG What size RMC do we need? A 3" B 3/4" C 1" D 1 1/2"
Please provide Handwritten answer. Electrical Engineering A 15 KHz tone is recorded at 8000 Hz. The frequency of the tone when played back at 8000 Hz is ____ KHz
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
22surse_assessment_id=_18982_1&course_id=_22058_1&content_id= _262244_1&ques * Question Completion Status > A Moving to another question will save this response. uestion 2 If the switch is closed for a long time and then opened at t-0. What is the initial value of the capacitor's voltage? ww None of the answers o 12 O Take Test: Quiz 2-. FUJITSU F10 F11 F12 Prt Scr E7 F8 F9 F6 Sys Rq ECO 7 V 8 A 9. 5 Y ! U P
Please, I need the final solution as soon as possible, I do not need any explanation or explanation
Please answer quickly. 17. The filament of incandescent lamp is usually made of: a. copper b. silver c. aluminum d. tungsten 18. A current measuring instrument can be modified to measure voltages by: a. using thicker wire in the coil b. using a high resistance shunt c. adding resistance in series d. adding resistance in parallel 21. "When two power sources are connected in a series-aiding configuration, the output voltage equals the _____________" a. supply with the highest voltage b. supply with the lowest voltage c. difference of the two supplies d. sum of the two supplies