A 203-V battery, an inductor, and a resistor are connected in series as shown in the diagram below. A two-way switch makes it possible to include or exclude the battery. The switch that had been in position 1 for a long time is suddenly moved to position 2. (Enter your answers to at least two decimal places.) le AV (i) (ii) (a) What is the voltage across the resistor at the end of five time constants? (b) At this time, what is the voltage across the inductor? V

Q: When a capacitor is placed in an alternating-current (AC) circuit, the charge on its plates varies…

A: The current flowing through a capacitor is related to the rate of change of charge on its plates,…

Q: The switch in (Figure 1) has been open for a very long time. The switch is closed at tt = 0 s.…

A: Given, emf of the battery, ε = 170 V

Q: Consider the time ot = 2n. a) What total energy, W, is stored in the circuit? b) Write the…

A: (Note: I think there is a typing error in the question and it should be ω = 2π.Then the circuit…

Q: ou decide to use a toaster to toast a slice of bread using the wall outlet of your home. Knowing…

A: The resistance of the nichrome wire can be calculated using the formula: R=ρLA Where R is the…

Q: 2

A:

Q: 7. Assume that a 10.0 µF capacitor, a battery of emf &=12.0 V, and a voltmeter of 10.0 MS impedance…

A:

Q: Consider the following resistive circuit. R1= 15 N R2= 5 Q R4 = 8 Q R3= 5 N What is the voltage drop…

A: Circuit diagram:

Q: Three identical lightbulbs, A, B, and C, are connected in the circuit shown in (Figure 1). Figure <…

A:

Q: Can you help me solve a simple circuit. I'm having trouble finding the current and voltage drop…

A:

Q: A DC circuit problem (see the circuit below) (need to see the loops you are using, so please label…

A:

Q: In the circuit of the figure & = 1.70 kV, C = 9.50 µF. R = R2 = R3 = 0.750 MQ. With C completely…

A:

Q: A battery with ? = 6 V and no internal resistance supplies current to the circuit shown in the…

A: a. When the switch is open, then the resistances R1, R2, and R3 are in series connection, so…

Q: Question: Choose the correct answer consi der(V=20v,R1-300O,R2-4000,R3-5000)for the electric circuit…

A: SOlution: Given that V = 20 V R1 = 300 Ohm R2 = 400 Ohm R3 = 500 Ohm

Q: The rod shown below moves to the right on essentially zero-resistance rails at a speed of v=2.20…

A:

Q: In the circuit shown, E = 4V, R₁ =43, R₂ = 72 , and C = 14 µF. I₁* Initially, the capacitor is…

A: Voltage of battery (V) = 4V R1= 43 ohm. R2= 72 ohm. C= 14 micro farad.

Q: In the circuit of the figure below, ℰ = 3.0 kV, C = 6.0 μF, R1 = R2 = R3 = 0.72 MΩ. With C…

A:

Q: Draw all possible loops separately to analyze the given electrical circuit. Identify possible…

A:

Q: A battery with E = 7.60 V and no internal resistance supplies current to the circuit shown in the…

A:

Q: The switch is thrown to close at t=0. Find i¿(t) for t>0 in the network. RI R3 Ike 3 KSL 10 v (t TH…

A: Given The switch is thrown to close at t=0. Find iL(t) for t&gt;O in the network, as following…

Q: Q8. The points A, B and C in the circuit below can be individually switched to connect either to +V…

A: In the logic Function GND =0+V=1

Q: R Consider an RL circuit as shown in the Figure with V = 5 V, L = 10 mH, and R = 2000 Q. After the…

A: V = 5 volts L = 10 mH = 0.01 H R = 2000 ohm

Q: The current in an RL circuit builds up to one-third of its steady-state value in 4.04 s. Find the…

A:

Q: Find the charge on the capacitor in an LRC-series circuit at t0.03s (find the charge g(t) and then…

A: The charge on the capacitor is 3.4118 C

Q: Consider the circuit shown in the figure below. (Assume L = 5.25 mH and R, = 455 N.) S L. 9. 24.0 V…

A: In this question we have to find the value of R1 and the current in the inductor of position b

Q: Consider the circuit below. The capacitor has a capacitance of 11 mF and starts out uncharged. The…

A:

Q: A complicated RC circuit is shown in ( Figure 1), with R₁ = 15Q₁R₂ = 20, R₂ = 40₁C₁ = 16µF, 1 2 1…

A:

Q: #1 - You are designing a circuit to run the variable intermittent windshield wipers for a car. You…

A:

Q: Attached is the picture with the question on it, but here are the questions typed out if its hard to…

A:

Voltage Across Inductor

An actor is a passive electrical component that consists of a coil bent in the form of wire which uses electromagnetism to produce electric current through the coil. When the electric current flows through a conductor that is the coil, a magnetic flux is developed around the conductor. This flow of current through the coil creates a magnetic field based on Fleming's Right-hand thumb rule. If there is any decrease in the current passing through the inductor, then the magnetic field will also decrease and energy is released through the generation of electric current. There is also a secondary voltage inducing in the same coil due to the magnetic flux, since it opposes any changes in the electric current flowing through the circuit. An inductor is also called choke, coil, or solenoid. A choke is designed to block certain frequencies when the DC current passes. A winding coil is coated with insulation to give extra insulation and protect the circuit. They are usually tightly wrapped around a central core which is cylindrical in nature so that the magnetic flux can be induced. The solenoid is a three-dimension coil that is used to exhibit electromagnetism when the magnetic field is developed due to the current flowing through the coil. The sign convention of the inductor is the same as the power dissipating device. When the current flows into the positive side of the voltage across the inductor, the value is positive and the inductor dissipates power whereas when the inductor releases the power back to the circuit, the current has a negative sign convention.