A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force P is applied the block deforms into the shape shown by the dashed line. Determine the magnitude of P. The block's material has a modulus of rigidity of G = 26 GPa. Assume that the material does not yield and use small angle analysis. 150 mm- 0.5 mm

A 20-mm-wide block is firmly bonded to rigid plates at its top and bottom. When the force P is applied the block deforms into the shape shown by the dashed line. Determine the magnitude of P. The block's material has a modulus of rigidity of G = 26 GPa. Assume that the material does not yield and use small angle analysis. 150 mm- 0.5 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stepped rod is made up of two different materials A and B of lengths 80 cm and 1.2 m respectively. The diameters of materials B and A are 2.5 and 3.5 cm respectively. The modulus of elasticity of materials A and B are 250 and 150 GPa respectively. The elongation of the rod is the same for both the materials. A total tensile load of 40 kN is applied to both the materials A and B together. Calculate the load in each material.
The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an inner diameter of 15 mm and an outer diameter of 25 mm. The original lengths of the bolt and sleeve are 80 mm and 50 mm, respectively. If after the nut on the bolt is tightened the tension in the bolt is 10 kN, determine the change in dimension of the cross-section of the bolt and the sleeve. Assume the material at A is rigid. E = 70 GPa, Emg = 45 GPa, Ga = 26 GPa, Gmg = 17 GPa.
A uniform edge load of w1 = 530 lb/in. and w2 = 320 lb/in. is applied to the polystyrene specimen. Ep = 597(103)psi and νp = 0.25. 1) Part A: If the specimen is originally square and has dimensions of a = 1 in ., b = 2 in., and a thickness of t = 0.35 in. , determine its new dimension a′ after the load is applied. 2) Part B: Determine its new dimension b′ after the load is applied. 3) Part C: Determine its new dimension t′ after the load is applied.
The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.47 in., -0.16 in.). Assume a - 17 ft, b-34 ft, c-12 ft, and d - 24 ft. Determine the normal strain in each bar. Answer: EAB- T EBC i P a e (1) B UE με b (2) C d
The 1900-NN load is applied along the centroidal axis of the member. (Figure 1) Determine the magnitude of the resultant internal normal force in the member section a-a. Express your answer to three significant figures and include the appropriate units. 2) Determine the magnitude of the resultant internal shear force in the member section a-a. Express your answer to three significant figures and include the appropriate units.
A 25 mm square-cross-section bar of length 300 mm carries an axial compressive load of 50 kN. Determine the stress set up in the bar and its change of length when the load is applied. For the bar material E = 200 MPa
8-21. The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.8 mm. When the applied load on the specimen is 50 kN, the diameter is 12.67494 mm. Determine Poisson's ratio for the material. 8-22. The elastic portion of the stress-strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm and a gage length of 50.8 mm. If a load of P = 60 kN is applied to the specimen, determine its new diameter and length. Take v = 0.35. σ (MPa) 490 0.007 Probs. 8-21/22 € (mm/mm)
*3-12. Fiberglass has a stress-strain diagram as shown. If a 50-mm-diameter bar of length 2 m made from this material is subjected to an axial tensile load of 60 kN, determine its elongation. σ (Pa) 300(10%) 1/2 €(mm/mm)
Determine the maximum compressive force that can be applied on a circular member of diameter 40 mm. The compressive strength of the member is 90 kPa.
The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 300 N is applied to it, determine the change in its length and the change in its diameter. Ep = 2.70 GPa, np = 0.4.
The stress–strain diagram of the material can be approximated by the two line segments. If a bar having a diameter of 80 mm and a length of 1.5 m is made from this material, determine the critical load provided the ends arepinned. Assume that the load acts through the axis of the bar. Use Engesser’s equation.
Part A A FA. FD= -600 mm- P 50 mm VE ΑΣΦ 41 B vec - 600 mm 25 mm If the gap between C and the rigid wall at D is initially 0.15 mm, determine the magnitudes of the support reactions at A and D when the force P = 200 kN is applied. The assembly is made of A36 steel. (Figure 1) Enter your answer, separated by a comma. -0.15 mm D ? kN