A 20-kg crate is subjected to force F = (2s2 + 3)N, where s is the displacement in meter. If the coefficient of friction between the surface is 0.20, what is the speed of the crate when it travels 10 m starting from rest?

A 20-kg crate is subjected to force F = (2s2 + 3)N, where s is the displacement in meter. If the coefficient of friction between the surface is 0.20, what is the speed of the crate when it travels 10 m starting from rest?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: An 80 kg block sits on top of a hill with height h1 = 3 metres and slides down to a 3 metres long…

A: Consider the diagram shown below for the given system.

Q: The initial position of the 7 kg-block is at x1 = 13.75 cm. The final position of the block is…

Q: A 3.00-kg object is acted upon by an applied force causing it to move along a rough horizontal…

A: Given data: m=3 kgx=5t2−1y=3t3+2μk=0.4μs=0.8

Q: A 3 kg box is sliding across a frictionless table at a rate of 5 m/s. It encounters a 35° incline…

Q: For the system of blocks shown, a horizontal force P impends the motion of block A upwards. The…

Q: A box with a mass of 100 kg was originally attached to a spring in position A. After that, pressure…

A: According to the given data m=100 kg x=1 m μ=0.3 k=2 kN/m We need to determine the distance S…

Q: A 10 lb block slides 6 ft down a plane inclined 40 degrees with horizontal. Determine the work done…

Q: e acceleration of ассe

A: To find Acceleration of the object

Q: A block of mass 2.35 kg is pushed up against a wall by a force P that makes an angle of 50.0° angle…

A: According to the given data m=2.35kg θ=50 μ=0.221 Weight of block=2.35x9.8=23.03N we need to find…

Q: What should the mass m (kg) be for the system given in the figure to remain at rest? There is…

A: Draw the free-body diagram for the above system.

Q: A 25 kg crate has a speed of 2 m/s when a forces of F = 0.5(s)+75 N is applied (where t is in…

A: The frictional force is directly proportional to the normal force of the object.According to the…

Q: A 10-kg crate, starting from rest, is pulled across a floor with a constant horizontal force of…

Q: A 10 kg block is moving on a horizontal table. The coefficient of kinetic friction between them is…

A: Given: Mass of block is 10 kg. The coefficient of kinetic friction is 0.3.

Q: increases to F, 80 lb once in the pool. What is the speed of the raft when s = 5 ft?

Q: Q1) A 5 kg block initially at rest is pulled to the right along a horizontal surface by a constant…

Q: 3 m/s. A 20 ton railway wagon is coupled to three stationary railway wagons of the same type with v…

Q: problem is to find how far does the plane go before it comes to stop. Assume, when the plane snags…

A: Given: mp=1200 kgms=130 kgvp=35 m/sμk=0.4F=1400 N To determine: how far does the plane go before it…

Q: The mass of blocks A and B shown in the figure below are mA = 5 kg and mB = 35 kg, successively. The…

A: given mass of the block A, ma=5kgmass of the block B, mb=35kgcoefficient of friction between blocks…

Q: In the given figure below, a 3.0 -kg block is sliding down a 60o-rough incline. The speed of the…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: A block of mass 17.8 kg lies on a horizontal plane. A force F that is inclined 41° with the…

Q: A car travelling in a constant velocity wants to turn in a 10m radius flat curve. If the…

A: We know that, force of static friction enables the car to remain in its circular path, thus we…

Q: With the radius of curvature (r) at the top of the loop (T) is 1 m. Determine the minimum speed (in…

A: Given data: mass = 0.1 kgradius of the loop =1 m

Q: A rope of length L = 1.5 m and mass m = 2.3 kg is initially at rest and can slide on an inclined…

A: b = 0.22 μk=0.47

Q: An 8.70-kg block slides with an initial speed of 1.56 m/s up a ramp inclined at an angle of 28.4°…

A: Given data as per the question Mass of block =8.70 kg Initial velocity =1.56 m/s inclination angle…

Q: A test rocket is fired straight up from rest with a net acceleration of 20.0 m/s². After 4.00…

A: Given data: u=0 m/sa=20 m/s2t=4 sec Need to determine the maximum elevation (height) does the rocket…

Q: Determine the horizontal force required to move a 2500-lb automobile with 23-in.-diameter tires…

A: Given Weight of the automobile = 2500 lb Diameter of the tyre = 23 in Coefficient of rolling…

Q: A rope of length L = 1.5 m and mass m = 2.3 kg is initially at rest and can slide on an inclined…

Q: a) The limiting speed of the mini bus on this curve. b) The normal reactions developed at the inner…

A: we are to calculate the limiting velocity and normal reactions on the tyres

Q: A manufacturer is carrying out a vehicle performance analysis and subjects to a road test. The…

Q: How much breaking speed does the cable car need to descend at a constant speed? One day the brakes…

Q: A 100 lb force exerted against a 1000-lb block causes the block to slide with constant velocity. The…

Q: A helicopter with a mass of 10,000 kg takes off straight up at t=0. The thrust of the engine is…

Q: An 2.00 kg box is initially at rest on a ramp inclined at 23° below the horizontal. The coefficient…

Q: In the given figure below, a 3.0 -kg block is sliding down a 60°-rough incline. The speed of the…

A: we know the initial energy of the system =K.E of a block + gravitational P.E of…

Q: A force exerted on 20kg body and move it on a rough horizontal surfaceat constant acceleration of…

A: Given data: mass Constant acceleration distance moved x=6 m Co-efficient of friction

Q: Determine the normal force the box exerts on the surface when it reaches point B. Neglect friction…

A: Given Data:the mass of the box m= 8Kgthe velocity of the box at point A neglecting the friction and…

Q: (a) Draw the FBD of A and B when the wedge B impends to slide to the left. Friction is negligible…

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

A 20-kg crate is subjected to force F = (2s2 + 3)N,
where s is the displacement in meter. If the
coefficient of friction between the surface is 0.20,
what is the speed of the crate when it travels 10 m
starting from rest?
F

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Given:

VIEW

Solution:

VIEW

Answer:

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 100-lb block is pushed at constant speed for a distance of 20 ft along a level floor by a force that makes an angle of 35° with the horizontal, as shown in Fig. The coefficient of friction between the block and the floor is 0.35. Determine The work done on the block by gravity. F 35°
F A block of mass of 2kg is being pushed by of force F = 10 N at an angle of 0 = 30° to the horizontal. If the block starts from rest, what is its speed after it has travelled 5 meters Without friction, v = m/s With μk m/s - With Uk m/s 0.25, v= What if it starts with an initial speed of 5 m/s Without friction, v = m/s = BY UBC Engineering 0.25, v=
A horizontal force of 300 lbs pushes a 200lb block up an incline whose slope is 3 vertical to horizontal. If the coefficient of friction is 0.2 determine the time required to increase the velocity of the block from 10 to 50 feet per second.
A 85-kg man starts climbing a ladder that leans against a wall as shown in Figure Q1. If the ladder is 5 m long and weighs 10 kg. Determine how far up the ladder the man can climb (in m) before the ladder starts to slip if the coefficient of friction is 0.25 at the top vertical surface and 0.4 at the bottom horizontal surface.
I need the answer as soon as possible
2. A 20 kg box sitting on a horizontal surface is pulled by a horizontal force of 64 N. The coefficient of kinetic friction between the box and the surface is 0.2. (Draw free-body diagram here) vsebn lognA en MOIT ANIMAX MATUM70038 blow 10 ode no tos 2010 Owl I 02 sa 0£to shingem seer sosot toriso 21 to obutingam and count onOno gol a. What is the normal force acting on the box?ib et bas 1910 marsib vbod-seil wai(1) b. What is the force of kinetic friction acting on the box? od no oond ton silt ei tad s c. What is the acceleration of the box? rss sdr to noitestsson sdt at tod in
Q2: The system is released from rest with the cable taut. For the friction coefficients u, = 0. 35 and u = 0.25 , Neglect the small mass and friction of the pulleys. calculate the following. 1. The acceleration of each block. 2. The tension Tin the cable. 60 kg 3. The speed of the block B after 3 seconds from rest 20 kg 30° B
A man is driving his SUV with speed 54.0 mi/h on a horizontal stretch of road. (a) When the road is wet, the coefficient of static friction between the road and the tires is 0.103. Find the minimum stopping distance (in m). m (b) When the road is dry, μs m = 0.597. Find the minimum stopping distance (in m).
If use please use g = 9.8 m/s2
A 40 lb block is on a horizontal surface. A force of 70 lb is applied to the block parallel to the surface. The coefficient of sliding friction is 0.2. What is the acceleration of the block?