A-20 in Oil SG 0.86 51t 0.8 t A-50 in. SG 2.5

Q: In the figure shown, gear A rotates at 300 rpm. Gear S is fixed and has 80 teeth. The three…

A: Write the given data. Speed of arm, Narm=180 rpmSpeed of anulus gear, NA=300 rpmSpeed of gear S,…

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: You are given two shafts of equal lengths and made from the same material: a hollow shaft, with an…

A:

Q: The first gear in a single - stage gear train has 42 teeth and an angular velocity of 2 revolutions…

A: Given,The first gear in a single - stage gear train has 42 teeth and an angular velocity of 2…

Q: A) Draw the two limiting positions of the following crank-slider mechanism. Indicate all known sizes…

A: Given:To find:(a) Draw the two limiting positions.(b) Determine the piston stroke.

Q: Write a CNC program code to machine this part.

A: Since the part is symmetrical, thus divide the given component into half and the half part.

Q: A drilling machine is to have 8 speeds ranging from 100 rev/min to 1000 rev/min. if the speeds from…

A: The total number of terms for this AP is: n=8 The first number is: a=100 rev/min The last number is:…

Q: Calculate the pitch diameter of a M10 × 1.5

A: given data; Calculate the pitch diameter of a M10 × 1.5

Q: Two meshing spur gears with a diametral pitch of 4 teeth per inch and a pressure angle of 20 degrees…

A:

Q: If a spur gear has a pitch of 18 teeth per inch and 29 countable teeth, what is the diameter of that…

A: Pitch, P= 18 teeth per inch Number of teeth, T= 29   To find: Diameter of the gear in inches, D

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: A gear train consists of three gears: a pinion (which is the driver), an idler, and a gear (which is…

A: Given:- The gear train of three gears Tidler=68  Tidler(to replace)=37 To find:- Velocity ratio…

Q: For the following thread designation, turns, how far have you advanced the O 083 inches O 417 inches…

A:

Q: Given a gear of 32 teeth and 6 diametral pitch. Find the pitch diameter, outside diameter, tooth…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Gear 2 in the diagram below is driven at a speed of 126 revolutions per minute. Gear 2 has 16 teeth,…

A: The gear train is simple,The speed ratio of a simple gear train with 2 gears is as follows,Here,N is…

Q: For practical working gears as manufactured, typically the addendum, a, is larger than the dedendum,…

A: Addendum: The distance between the top land and the pitch circle on a gear tooth, is called as…

Q: f e (D d b C a k j a=38.0 b=41.5 c=39.3 d=40.1 e=55.8 f=39.4 q=36.7

A: a = 38.0b = 41.5c = 39.3d = 40.1e = 55.8f = 39.4g = 36.7h = 65.7i = 49.0j = 50.0k = 61.9l = 7.8m =…

Q: If gear 1 turns 620 degrees, how many degrees will gear 3 turn? N1 =20, N2

A:

Q: The answer is one of the options below please solve carefully and circle the correct option Please…

A: Given Gear train arrangement To find Gear train which will be effective for bearing

Q: In the gear train shown gear 3 is carried on arm 5, Gear 3 meshes with gear 2 and gear 4. The number…

A: Here, Gear 2 is sun gear. Gear 3 is planet gear. Gear 4 is annular gear. Link 5 is arm.   From the…