A 2-wire d.c. distributor cable AB is 2 km long and supplies loads of100A, 150A,200A and 50A situated 500 m, 1000 m, 1600 m and 2000 m from the feeding point A. Each conductor has a resistance of 0•01 Ω per 1000 m and 300 V is maintained at point A. Calculate the resistance between point EB. *

Q: Q2) In the load test, is the iron loss present?

A:

Q: The cost of a single phase cable is (20000A+2400) per Km where A is the area of the cable in cm2. If…

A: As per Kelvin's law, the annual interest and depreciation on the capital cost of the conductor…

Q: The spiraling is one of the factors which effect the resistance of the conductor. Select one: True…

A: Resistance is increased because the outside strands are larger than the inside strands on account…

Q: AV Şekil 1 Şekil 2

A: The phase displacement between voltage and current can given us an idea about the type of load…

Q: A 208-volt 3-phase circuit that draws 10-amps is installed in a raceway that measures 200ft, the…

A:

Q: A 250 m, 2-wire d.c. distributor fed from one end is loaded uniformly at the rate of 0·8 A per…

A: Given values are = Voltage at far end is Vd = 250 Volt.

Q: 71. A single-core cable has a conductor diameter of 1 cm and insulation thickness of 0-4 cm. If the…

A: Given, A single core cable inner diameter, d1=1 cm=1×10-2 m…

Q: A 2-wire d.c. distributor cable AB is 2 km long and supplies loads of 100A, 150A,200A and 50A…

A: It is a two wire distribution system with distributor fed at one end: Here, the distributor is fed…

Q: 2. A uniformly distributed load on a distributor of length 500 m is rated at 1 A per metre length.…

A: Given: The length of the distributor is l=500 m. The current is i=1 A The voltage is V=220 V The…

Q: 5. Atwo wire DC distributor 0.8 kilometer long is supplying two loads 10A and 20A at 500 meter and…

A: Note: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: What is the percentage load to added to a branch circuit conductor having an ampacity equal to or…

A: Option d is correct 125%

Q: The figure below shows a ring distributor with interconnector BD. The supply is given at point A.…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: A d.c. Distributor AB, 2-wire, 800 m long is fed from both ends at 240 V. Loads of 30 A, 40 A, 50 A…

A: In this question we need to find a minimum consumer voltage.

Q: In a 3-phase 4-wire system, the currents in R, Y and B lines under abnormal conditions of loading…

A: Given:

Q: q) 150 kv single core cable has a radius of cable of 5cm. The insulation martial has two layers. The…

A: This is q very good question based on power system topic of transmission. Here we have to find the…

Q: A No.10 AWG copper conductor with THHN insulation has a one- way length of 100ft. It is carrying a…

A: In this question,  We need to calculate the voltage drop in the circuit.  If current I= 16A Find the…

Q: V- 2.5 V re L) In a test to determine the resistance A a cable, an applied was necessary to produce…

A: The correct solution can be achieved as follows.

Q: 1. A2-wire d.c. distributor A B is fed at both ends at the same voltage of 230 V. The length of the…

A:

Q: A uniform 2-wire d.c. distributor 650 meters long is loaded with 0.28 ampere/ meter and is fed at…

A:

Q: Due to the poor tensile strength alone cannot be used as an overhead line conductor. Aluminum O…

A: We know that since graphite is a brittle and porous material and its tensile strength is low.

Q: A d.c. distributor AB is fed at both ends. At feeding point A, the voltage is maintained at 235 V…

A: Given: In this question, the given details are, A d.c distributor AB is fed at both ends. At feeding…

Q: -advantages and disadvantages of Series and parallel connections of solar cell ? B-Which of the…

A: Series: S.NO Advantages Disadvantages 1 Voltage rating can be increased If any cell gets…

Q: 8. The resistance of a conductor depends only on the cross sectional area of the conductor. True…

A: The resistance of a conductor is given by R=ρLA Where ρ is resistivity, L is length of conductor and…

Q: Correct statement related to weight of conductor and sag is .............................. Weight of…

A: The correct statement related to weight of conductor and sag is given below weight of conductor is…

Q: om both s of 20 A are of 100m D0 m fror ely. If the

A: The distribution system is a part of the power system which comes under service mains. It is…

Q: A2-wire d.c. distributor AB is 300 meter long. The end A is fed 205 V and end B at 200 V. The…

A: Given data: Resistance = 0.15 Ω/km The potential at point A is 205 V. The potential at point B is…

Q: A4 True/False The conductor resistance increases with increase in temperature.

A: In this answer let us try to understand how the resistance of the conductor changes with the change…

Q: Determine the insulation resistance of a single-core cable of length 3 km and having conductor…

A:

Q: The increase of the temperature of conductors(cables) used for the transmission of electrical power…

A: The increase in the temperature of the conductor will increase the resistance of the conductor…

Q: inm do A ☺ 52

A: From the mesh Analysis

Q: A 2-wire d.c. distributor AB is fed from both ends. At feeding point A, the voltage is maintained as…

A:

Q: A2 TW conductor is instaled in a location where the ambient mperature is expected to be 102 F. The…

A:

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.