A d.c. distributor AB is fed at both ends. At feeding point A, the voltage is maintained at 235 V and at B at 236 V. The total length of the distributor is 200 meters and loads are tapped off as under: 20 A at 50 m from A 40 A at 75 m from A 25 A at 100 m from A 30 A at 150 m from A. The resistance per kilometer of one conductor is 0.4 22. Calculate the minimum voltage and the point at which it occurs.

A d.c. distributor AB is fed at both ends. At feeding point A, the voltage is maintained at 235 V and at B at 236 V. The total length of the distributor is 200 meters and loads are tapped off as under: 20 A at 50 m from A 40 A at 75 m from A 25 A at 100 m from A 30 A at 150 m from A. The resistance per kilometer of one conductor is 0.4 22. Calculate the minimum voltage and the point at which it occurs.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Sag increases when the conductor ages due to this effect. O A. STAY RELAXATION O B. THERMAL EXPANSION O C. METALLURGICAL CREEP O D. ELASTIC STRETCH
Problem#6 A 2-wire DC distributor AB is fed at both ends at the same voltage of 230 V. The length of the distributor is 500 metres and the loads are tapped off from the end A as shown below. If the maximum voltage drop of 5-5 V is to be allowed, find the X-sectional area of each conductor and point of minimum potential. Specific resistance of conductor material may be taken as 1-73 x 10-8 S2 m. 60 A 40 A 150 m 250 m Load: Distance: 100 A 50 m 100 A 400 m
I need the answer as soon as possible
Give the suitable solution for the following The non-conventional sources of energy are........ The diesel power station cannot be located at any place (T or F) The d.c resistance of various types of conductors at specified temperature (T) is found by...... The self-GMD of a conductor depends upon the ...... ...... and ..................of the conductor The voltage drop is increased if the length of transmission line is increased (T or F) The skin effect depends upon the.............. ........ and ********* , and..... …........
10/ Sag increases when the conductor ages due to this effect. A. THERMAL EXPANSION B. ELASTIC STRETCH C. METALLURGICAL CREEP D. STAY RELAXATION
b) Explain why the effective length is less than the lotal length of a laminated armature .Which value should be used for L in Ecotl DLN»B and Trol- NDLIcoB? Which value should be used in resistance calculations?
In a 3-phase 4-wire system, the currents in R, Y and B lines under abnormal conditions of loading are 11=100 A, (angle 30 degree), 12=300 A (angle 300 degree), 13=100 A (angle of 180 degree). The current in the neutral wire is: Select one: O a. None of above Ob. 13 A O c. 51 A O d. 150 A O e. 250 A
Q.,C
The number of disc insulators used in a suspension insulator setup with string efficiency 80 %, phase voltage 33 kV, and the voltage across insulator nearest to conductor 9 kV is
Solve showing all the steps in detail
Answer the following quastion * 150 kv single core cable has a radius of cable of 5cm. The insulation martial has two layers. The relative permittivity of the first and second layers are 6 and 3 respectively. If the minimum electric stress of the first and second layers are 30 kv/cm and 20 kv/cm respectively. Find the maximum electric stress of the first layer
The number of disc insulators used in a suspension insulator setup with string efficiency 80 %, phase voltage 33 kV, and the voltage across insulator nearest to conductor 10 kV is .