Answered: A 15 mm diameter steel bar was bent as…

A 15 mm diameter steel bar was bent as shown. Using the work and energy method, determine the deflection at end C due to the force P of 200 N. Use E = 200 GPa and G = 77 GPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q2/ For the truss show in fig. Determine the horizontal deflection at joint G, using virtual * work…

Q: Based on your b and considering a positive bending moment of 58kNm, determine the tensile and…

A: Neutral axis will pass through midpoint of AC or BD

Q: In the figure shown, each of the four vertical links connecting the two rigid horizontal members is…

Q: 4. The steel (E 29(10)³ ksi) beam is subjected to the loading shown. Using Castigliano's theorem,…

A: The elasticity of steel is

Q: The rigid arm AB is attached to the end of the solid circular steel rod BC. The rod is supported by…

Q: D Using the method of work and energy, determine the deflection at point D caused by the load P. L.

Q: Determine its minimum required diameter

A: for solution refer below images.

Q: Using an energy or work approach, determine the vertical deflection of point C and the deflection of…

Q: A circular rod made of aluminum with a radius of 32.5 mm was placed in a steel tube with a length of…

A: Given data, rAl = Radius of the aluminum rod = 32.5 mm L= Length of the rods = 2.4 m = 2400 mm rs,i…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

Q: Determine as expressions of the elastic line, the deflection and the large at point B. E = 200 Gpa…

A: To find equation of elastic curve and deflection at point B

Q: 7. Straight rods of 0.4ft diameter and 100ft length are stored by coiling the rods inside a drum of…

Q: Prob 2. The cantilever beam below is made of steel (E200 GPa) and must support the distributed load…

A: To Find : a) The location and magnitude of the maximum bending moment and draw the V and M diagram.…

Q: 4 kN/m B .1 m

A: GIVEN DATA SIMPLY SUPPORTED BEAM WITH UDL DIAMETER = 3inches = 76.2mm E=200GPa WE HAVE TO CALCULATE…

Q: A mild steel strut is of single angle section 100 mm x 75 mm x 8 mm. Its length is 3m wiun both ends…

A: Stress When body is subjected to a load then body will get deform but body will resist the…

Q: 5. The rigid beam rests on two short posts AC and BD as shown. Post AC is made from steel with E =…

A: GivenEs=200GPaEal=70GPadst=25mmdal=40mm

Q: An 8-m cantilever beam has a uniformly distributed load of 12 kN.m throughout its entire length and…

Q: Problem4: For the beam and loading shown, determine the deflections y and the slopes 0 at B and at C…

Q: The beam shown below is suspended from two steel rods as shown and is initially horizontal. The…

A: First let us find the forces acting on rod AD(FAD) and CE(FCE), Due to symmetry , FAD = Q/2 and FCE…

Q: 8

A: Step 1:Step 2:

Q: A cylindrical hollow shaft shown is subjected to a compressive load acting though its longitudinal…

A: Step 1: Step 2: Step 3: Step 4:

Q: A 4in ductile iron pipe carries 0.20 ft3/s of glycerin (SG=1.26) at 100°F. Is the flow laminar or…

Q: 4. A cantilever of length 2m carries a point le kN at its centre. If E = 10 N/mm?and I 10 area…

Q: Consider a simple supported beam subjected to the load shown. The beam has a solid circular…

Q: A composite beam is fabricated by bolting two 3.8-in.-wide by 13-in.-deep timber planks to the sides…

A: Given Data: wt=3.8 inht=13 inws=0.7 inhs=13 inEt=1730 ksiEs=30400 ksiL=16 ftLAB=LCD=4 ftLBC=8…

Q: A 14-in round wire coiled to form a conical spring with 10 effective coils & an outside diameter of…

Q: 3. A circular flat plate of 120 mm diameter and 6-35 mm thickness is clamped at the edges and…

A: Given data Diameter of flat plate = 120 mm = 0.12 m Thickness = 6.35 mm = 0.00635 m Uniform lateral…

Q: For the truss shown below, determine the horizontal deflection of joint B by using the virtual work…

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

A: given; lets take reaction force at A=RAw=15KN/mL=3.5mE=185GPaI=110*106mm4AB=L/2BC=L/2AC=L

Q: 6 kN 2 m 1m C

Q: P-30 IN Q1/ Two solid cylindrical rods are joined at B and loaded as shown. Rod AB is made of steel…

Q: SOLVE BY HAND LEGIBLE DETERMINE THE FINAL REACTIONS IN THE FOLLOWING BY THE SLOPE DEFLECTION METHOD.…

A: 📍 Approach to solving the question: Step 1: Calculate Fixed-End Moments (FEMs) Fixed-end moments…

Q: Given those members (1), (2), and (3) have Young's modulus E =107 psi and a yield stress o_y= 60 ×…

A: Young's modulus: E=107 psi Diameter of the member: d=1 in Load: P=10 kips The expression for Euler's…

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

A 15 mm diameter steel bar was bent as shown. Using the work and energy method, determine
the deflection at end C due to the force P of 200 N. Use E = 200 GPa and G = 77 GPa.
B
250 mm
250 mm
A
P = 200 N
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given:

VIEW

Step 2: To find the strain energy due to bending and torsion

VIEW

Step 3: To find the deflection at point c using the strain energy method

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

vi) Using Macauley’s method, determine the deflection of the member at the locations where the 25 kN, 20 kN and 50 kN point loads are applied. Comment on how the maximum deflection of the member could be determined. Material properties for steel: Maximum allowable tensile stress = 750 MN/m2 Maximum allowable torsional shear stress = 375 MN/m2 Young’s Modulus of elasticity = 205 GN/m2Modulus of rigidity = 81 GN/m2Poisson’s ratio = 0
Problem 1: Steel rod AC (E=200GPA) having a cross sectional area of 250 mm?, jointly support the 10 kN load with spring DE having a flexibility of 0.0005mm/N and an unstretched length of 9m. Bar BCE is rigid. Assuming that there was no slack or stress in rod AC or spring DE before the load was applied; a. Determine the ratio of the deformation of rod AC to spring DE. b. Determine the force on rod AC in kN. 12m 9m E c. Determine the force on spring DE (kN). 12m 4m
For the hollow shaft shown, the strength is 150 MPa. Determine 1. The internal reactions due to external loads Fe. 2. Factor of safety for this bar Di=10 mm Fe=40 kN Do=30 mm
1. A cantilever of square cross section as shown was made of mild carbon steel SAE 1020, as rolled, and was designed to support a static load W = 15 lb. After the beam was installed, it was discovered that the weight W was not static but vibrated, so that actually the beam was subjected to a repeated load. Measurement showed that the weight rose and fell a distance h equal to 0.05 inch. Shortly thereafter the beam fractured at the fillet which had a machined radius of 1/32 in. (a) Make calculations to show and state your conclusion whether or not the beam should have been expected to fail. (b) for the same data, design a new cantilever with the same dimensions except with a fillet radius r= 1/8 in. Determine whether a carbon steel would be necessary, and if so, its SAE or AISI no. 1/2" 3/4". 6"
Please answer the given problem as soon as possible with complete diagrams and solutions. Thank you!
The beam shown has an overall length L of 5.9 metres. A uniform distributed load of 7.8 kN/m is applied as shown. If the distance x is 2.3 metres, determine the magnitude (in kNm) of the reaction moment at A. Note: Do NOT include the units in your answer.
A uniform load of 8 kN/m acts on segment BC of the rigid beam shown. The beam is supported by a steel rod BD having a cross sectional area of 200 mm2. Determine the vertical displacement of the beam at C after the distributed load is applied. For steel, E = 200 GPa. Neglect the weight of the beam. Express your answer in mm.
Draw the shear stress diagram and bending moment diagram for a beam with the free body diagram shown below. Identify the location of critical point(s) in the beam. Given AB = 0.5 m, BC = 0.6 mm, and CD = 0.5 m.
Fmax= 13.14 kN Deflection max = 22.9mm
For the beam and loading shown, integrate the load distribution to determine (a) the equation of the elastic curve, (b) the deflection at the left end of the beam, and (c) the support reactions By and MB. Assume that EI is constant for the beam. Let w0 = 6 kN/m, L = 4.5 m, E = 210 GPa, and I = 140 x 106 mm4.
A beam of circular cross-section has a length of 5m and is simply supported at its ends. It is required to carry a total load of 57 kN uniformly distributed over the whole length. If the maximum bending stress is not to exceed 13 MPa and the maximum deflection is limited to 4 cm, the diameter of shaft in mm is given by : (take E= 18 GPa.)
III. Using Three Moment Equation, determine all reactions at supports also, determine shear and bending moments with complete labels. Use I = 1/12 bh^3 and E = 2.15x10^7 KPa 1381 KN/m 1381 KN/m 690.5 KN/m D B 4.0 m 3.0 m 7.0 m 4.0 m b = 0.25m h = 0.50m 4.0 m b = 0.35m h = 0.70m b = 0.45m h = 0.90m