A 15 cm diameter pipe is under a load H=8m. If a nozzle of diameter 0.05m is placed, calculate the pressure just before the outlet (kg/m^2), the system power (kW) and the pipe length. Consider the losses as 4.75 V1^2/2g+0.039V2^2/2g, f=0.003

Q: Q=2000J ПЛЛЛЛЛ air V(m/s) D=0.1m Tout=? Air at (3.15x10^2) K is entering in a circular pipe at…

A:

Q: Water flows through the pipe contraction shown in Figure I. For the given difference in piezometer…

A:

Q: A pipeline with roughness ks = 1.0mm and diameter D = 8.8cm connects two reservoirs. The reservoirs…

A: Given:Surface roughness of the pipe, ks=1.0 mmPipe diameter, d=8.8 cm=0.088 mSurface elevation…

Q: 2. A pump is used to move water (p = 1000 kg/m³) from a lake into a large tank as shown below. The…

A:

Q: Oil is pumped from a very large tank (z1 = 150 m) to another tank (z2 = 200 m), located higher and…

A:

Q: (b) A conical tube length of 2.0 m is fixed vertically with its smaller end upwards as shown in…

A: Handwriting.jpg

Q: In the system of reservoirs shown below, the flow of Reservoir 1 to Reservoir 2 is Q=15 cfs. At…

A: Consider the given data

Q: Benzene flows in a pipe as shown in figure. Determine the pressure at point 2 if the pressure at…

A: Given that , P1=5.2 barQ1=0.5m3specific gravity of benzene =0.876D1=15 cm =0.15mD2=22.5cm…

Q: The uniform concrete block in (Figure 1) has a weight of 300 lb. The coefficients of static friction…

A: iven Data:

Q: If P = 290 N, determine the required minimum compression in the spring so that the wedge will not…

A: Write the given data with the suitable variables. μ=0.35P=290 Nk=15 kN/m   It is required to…

Q: (1) 3 m (2) B 20 mm bore diameter 60 mm bore diameter

A: Calculated volume flow rate.

Q: Galvanized iron pipes with a roughness height of 0.40 cm are used to deliver water from reservoir A…

A:

Q: The diagram in figure mm diameter to a very large tank where the free water surface is assumed to…

A:

Q: The water is flowing through a pipe having diameters 45 cm and 15 cm at sections tand 2…

A: Given data diameter at section 1 (d1) = 45 cm  diameter at section 2 (d2) = 15 cm  discharge rate…

Q: Q=2000J ПЛЛЛЛЛ air V (m/s) D=0.1m Tout=? Air at (3.15x10^2) K is entering in a circular pipe at…

A: Given data: Temperature of air at entry = T1 = 3.15 x 102 K = 315 K Pressure of air = P = 101325 Pa…

Q: Water is flowing in the pipe shown in the figure below, with the 7.50-cm diameter at point 1…

A:

Q: : For the multiple pipe system below, calculate (a) the flow in each pipe and (b) Q2, the gauge…

A:

Q: Only Handwritten solutions are allowed.

A: 1.2.3.

Q: Water flows through a 61-cm by 122-cm conduit at a flow rate of 2000 CMH. The horizontal conduit was…

A: Given:Size of the duct, A=61 cm* 122 cm=0.61 m*1.22 m=0.7442 m2Water flow rate, Q=2000…

Q: Water is flowing in a piping system as shown tin figure, Find the i. diameter of section 2 pipe. ii.…

A:

Q: Flow takes place between three reservoirs, as shown in Figure 1. The volume flow rate out of…

A:

Q: Water is flowing in the pipe shown in the figure below, with the 8.20-cm diameter at point 1…

A:

Q: 1) Water at temperature T=350 K and pressure 0.25 MPa flows upwards through a vertical pipe with…

A: Given:Water temperature, T=350 KWater pressure, P1=0.25 MPaPipe diameter, d=380 mm=0.380 mPipe…

Q: Calculate the mass flow rates for your main pipe and intersecting pipe using the instructions posted…

A: For the main pipe RE=500Dm=20 mmLm=400 mmβ=121° For intersecting ppe RE=5000Li=200 mmDi=18.5…

Q: The inlet pressure to a piping system is 440 kPa. The inlet pipe diameter is 0.6 m. What is the…

A:

Q: A Pelton wheel develops 750 kW under ahead of 200 m. Its nozzie has a diameter of 10 cm and losses…

A: We have given data: P=750 kW Gross head, Hg=200 m, d=10 cm=0.1 m, Cv=0.98hf=90 Q2 , Q is in m3/s

Q: Calculate the flow distribution in the system shown in the figure below. The liquid that is…

A:

Q: Q2: Water flow in a pipe as shown in the figure if the velocity of the fluid at section A is 1.8 m/s…

A:

Q: A fluid enters a pipe at speed v1=0.1 m/s. the diameter of the tube is d=200mm and the fluid flowing…

A:

Q: r=20mm, the friction factor , the shear stress at pipe wall and the head loss per meter of the pipe…

A: Given: s=0.85 ρ=850 kg/m3ν=1.8×10-5 m2/sD=100 mmQ=0.50 L/sTo determine:Center line velocityvelocity…

Q: Water at 20°C flows through the elbow as shown and exits to the atmosphere. The pipe diameter is D₁…

A:

Q: Air flows steadily from a tank pressurized to 3kPa through a pipe of diameter D = 0.03 m and finally…

A:

Q: Three pipes A,B and C connected in seies discharges 160 L/s of water. The properties of pipe: for…

A:

Q: Water exits from a large vessel through a smooth pipe, with a length L = 7 m and an internal…

A: Given data:Pipe length, L = 7 mPipe diameter, D = 5 cm = 0.05 mInlet loss coefficient, KL,1 =…

Q: Use Bernoulli's energy balance equation (E = PV + 0.5*mU2), assume volume flow rate remains constant…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.