A = 13.75 × 10³ mm? I = 26.0 × 106 mm4 I, = 141.0 × 106 mmª г-

Q: An angle member (L-section) is used as a beam. Note that the thickness for the flange and the web is…

A: Given Data: The value of M is, M=50 kN·m The angle from the horizontal is. θ=30° The value of SN is,…

Q: maximum normal stress that occurs

A:

Q: by m thick and e midpoint deflection is 24 O GPa. Answer must be ir

A:

Q: SAMPLE PROBLEM 2: VSE LRFD Steel column 3.6m long and hinged at both ends is used to carry an axial…

A:

Q: A flat steel bar, 29 mm wide by 4 mm thick and 1.8 m long, is bent by couples applied at the ends so…

A: Given data in question  Cross section Length Deflection  Elasticity modulus  To find out  Maximum…

Q: 8: A thin cylindrical has inner radius=450 mm, thickness=9 mm is subjected to internal Pressure of…

A: Given data : Radius (r)=450 mmInternal pressure (p)=20 MPaThickness (t)=9 mm

Q: A steel pipe is subjected to a quadratic distributed load over its height with the peak intensity qo…

A:

Q: W16

A:

Q: A solid aluminum shaft of 120 mm diameter fits concentrically in a hollow steel tube. Determine the…

A:

Q: An aluminum bar having a cross-sectional area of 160 mm² carries the axial loads as shown in the…

A:

Q: P2 Ans: 5000 For the cross sections shown in figure (a) and (b) compare the 0.005m 0.2m torsional…

A: Given data,  Inner radius = 0.2 m Thickness = 0.005 m   To find out the radio of Torsional rigidity.…

Q: The axially loaded steel material shown below has E = 29.000 ksi and vitel =0.30. Assuming that e, =…

A: As per Bartleby policy i can answer  only one question at a time. Please upload other questions…

Q: A beam with a T-section is supported and loaded as shown in the figure. The cross section has width…

A: A beam with the T section is given in the question all the loading condition is given in the above…

Q: Q1) Three bars AB, CD and ED are used to support ACE beam. The three bares have modulus of…

A: Draw the free body diagram. Equilibrium of vertical forces,…

Q: Figure Q4(a) shows a steel beam with length of 4 m that is supported by a steel column at point B.…

A:

Q: Consider the following figure. h B III (a) Determine the maximum tensile stress o, and maximum…

A:

Q: 1. Determine the nominal load P that will cause failure of the beam shown below. As part of your…

A:

Q: #3. The distributed load w is supported by three suspender bars as shown. AB and EF are made of…

A:

Q: 2. Determine the dimension "L" of the hollow pentagonal pedestal shown if it has to carry an ivory…

A: To find the dimension L of the Hollow Pentagon Diameter of the Hollow portion (Deven)= 35 mm…

Q: 8. A steel bar of 40mm x 40mm square cross-section is subjected to an axial compressive load of…

A:

Q: A flat steel bar, 27 mm wide by 3 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A:

Q: Read the question carefully. Give me right solution according to the question. Find the load P in…

A: given data:- yield stress due to bending=250 mpaelastic constant E =200000 moamoment of inertia of…

Q: An 8 m simple beam is loaded with a 228 kN point load at the first third of its length. The cross…

A:

Q: 3. Two bars are made of a material with the stress-strain diagram as shown. Find the cross-sectional…

A: Given :

Q: A rolled I-section beam is supported on a 75 mm wide bearing plate as shown in the figure. Thickness…

A:

Q: Assume the shapes shown below have the same material, cross-sectional area, overall depth, and…

A: Part 1  As shear stress is inversely proportional to the area of the flange. The section (b) will…

Q: The horizontal steel rod, 2.5 m long and 1200 mm2 in cross-sectional area is secured between two…

A: Length of rod=2.5m Cross sectional area of rod=1200mm2 E=200GPa

Q: A simple pin-connected truss is loaded and supported as shown. All members of the truss are aluminum…

A: Question is truss based problem in which a truss is composed of aluminium pipes and there diameter…

Q: A simple pin-connected truss is loaded and supported as shown. The load P is 160 kN. All members of…

A: Solution: Given: Load, P = 160 kN outside diameter = 130 mm Wall Thickness = 9 mm

Q: Calculate the absolute maximum stress in the steel in MPa. d. Calculate the stress in the steel…

A:

Q: A three part bar is connected to walls at D and C and loaded as shown. Middle section AB is solid…

A:

Q: An aluminum bar having a cross-sectional area of 160 mm² carries the axial loads as shown in the…

A:

Q: An 8 m simple beam is loaded with a 208 kN point load at the first third of its length. The cross…

A:

Q: A WT305 x 41 standard steel shape is used to support the loads shown. Assume w = 46 kN/m, LAB = 1.2…

A:

Q: In the figure, find the length c of the overhangs so that the beam made of U profile can carry the…

A:

Q: LOmPa aGMPa 30 MPa

A: Solution Given Data σx=30 MPaσy=10 MPaζxy=26 MPa

Q: A flat steel bar, 28 mm wide by 5 mm thick and 1.7 m long, is bent by couples applied at the ends so…

A:

Q: Combined Stress: 17a The cantilever beam shown below is loaded by P=20 kN load as shown. Find at…

A: Load, Normal stress, Width of section, Depth of section, To find: The angle to produce zero normal…

Q: In the figure, find the length c of the overhangs so that the beam made of U profile can carry the…

A:

Q: ouble tee cross section is used for the beam shown below. Assume the following lengths and loads: 14…

A:

Q: Shown below is a steel tube AB with a 1.5" outside diameter and .06" wall thickness. You may assume…

A:

Q: A flat steel bar, 25 mm wide by 2 mm thick and 1.5 m long, is bent by couples applied at the ends so…

A:

Q: The rigid platform shown has negligible mass and rests on two steel bars, each 250 mm long. The…

A: Compute the stress in the aluminum bar

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.