A 12-lb force P is applied to the control rod AB as shown. Knowing that the length ofthe rod is 5 in. and that a = 30°, determine the moment of the force about Point Bby resolving the force into horizontal and vertical components in lb-in. Write thenumerical value only and 2 decimal places. + for counterclockwiseAFa65°PB4 A 12-lb force P is applied to the control rod AB as shown. Knowing that the length ofthe rod is 5 in. and that a = 30°, determine the moment of the force about Point Bby resolving the force into horizontal and vertical components in lb-in. Write thenumerical value only and 2 decimal places. + for counterclockwiseAfa65°PB

torque is the rotational equivalent of linear force. It is also referred to as the moment, moment of…

Answered: A 12-lb force P is applied to the…

Similar questions

The answers are provided; please explain the purpose of each equation and why they were used Consider a bar of length 5.5 m, being acted on by three forces and constrained to rotate about its left end. The magnitudes of the first two forces are 19 N and 28 N and the first force is acting on the end of the bar at an angle of 43° What is the torque in newton-meters, due to F1 on this bar relative to the left end? Ans. = 78.87 Nm Equation used: τ1 = rFsinθ What is the torque in newton-meters, due to F2 on this bar relative to the left end, if this force is acting at the midpoint of the bar? Use a coordinate system with positive directed out of the screen. Ans. = 77 Nm Equation used: τ2 = F2 x (L / 2) What is the magnitude of the force F3, in newtons, if the force is a distance 0.85 m from the left end and the bar is not rotating? Ans. = 183.38 N Equation used: F = (τ1 + τ2) / d
Needs Complete typed solution with 100 % accuracy.
Please asap
Can you help me with a physics problem?There exists a uniform rod with a L length and a m mass that is held to a wall by a frictionless hinge at its base and by a horizontal string at a x distance from the hinge. See picture. 1. What is the tension in the string and the horizontal and vertical components of the hinge's force?2. Theoretically, if the string were to be cut. What would the angular acceleration of the rod be just after it has been cut?
20kg mass is at the 1.25 meter mark. Package G is at 1 meter mark. What must the mass of object G be? Calculate the torque that each object creates. The 20 kg mass on the left creates a positive torque. If the system is in equilibrium, the magnitude of the torque on the right must equal the magnitude of the torque on the left.
Needs Complete solution with 100 % accuracy don't use chat gpt or ai plz plz plz.
What is the torque from the horizontal force F → about the center of the sphere?
A linkage undergoing motion as shown. The velocity of the block, vp, is 4 m/s. The length of the rods is l=0.5m. l 45° -90° 45° l 121 No What are the angular velocities of links AB and BD in rad/s. Note: They both have the same angular velocity due to the symmetric geometry. Give your answer with 2 decimals.
Needs Complete typed solution with 100 % accuracy.
A disk drive with a radius of 0.065 m starts rotating from rest with a constant angular acceleration. It takes 2.5 seconds to complete ten revolutions. One complete revolution takes how long? What is the linear displacement of the rim after ten revolutions? Determine the angular acceleration of the disk in radians per second squared (rad/s^2). Please provide work so I may better understand, thank you.
An engineer trying to determine whether or not her crane can lift loads (at the position shown), Her crane has a 5K chassis and 40K counterweight. Assume all other parts of the crane have negligible weight. 5ft Answer all questions relative to the rotation point. How much torque is caused by the chassis? unit v How much torque is caused by the counterweight? unit v How heavy of a load would "barely balance" the crane? unit BARNHART weight Could the crane lift the following loads without tipping over? 15K yes or nov 20K yes or nov 25K yes or novv 30K ves or nov cannot be determi check answers finalize (after completing ALL problems) Cop
Suppose you exert a force of 172 N tangential to a 0.295 m radius 75.0 kg grindstone (a solid disk). (Give your answers to at least 2 decimal places.) (a) What torque (in N · m) is exerted? (Enter the magnitude.) N. m (b) What is the angular acceleration (in rad/s2) assuming negligible opposing friction? (Enter the magnitude.) |rad/s? (c) What is the angular acceleration (in rad/s?) if there is an opposing frictional force of 22.6 N exerted 1.75 cm from the axis? (Enter the magnitude.) |rad/s?

SEE MORE QUESTIONS