A 12 × 12 column of Hem Fir, No. 1 grade, is 12 ft highand carries a compression load of 24 kips that is 9.5 in. eccentric from thecolumn axis. Investigate the column for combined compression plus bendingusing the ASD method.

A 12 × 12 column of Hem Fir, No. 1 grade, is 12 ft highand carries a compression load of 24 kips that is 9.5 in. eccentric from thecolumn axis. Investigate the column for combined compression plus bendingusing the ASD method.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Rafters are to be used on 24-in. centers for a roof span of16 ft. Live load is 20 psf (without snow)…

A: Given:- 24 in centers rafters span = 16 ft Live load = 20 psf Dead load = 15 psf To find:- a) Rafter…

Q: No. 1 grade of Douglas fir–larch is to be used for a series offloor beams 6 ft on center, spanning…

A: Given Total distribution load, W=3200 lb Length of the beam , L=14 ft Series of floor beams 6 ft on…

Q: A simple beam of Hem Fir, select structural grade, has a span of 18 ft with two concentrated loads…

A: Step 1: Step 2: Step 3: Step 4:

Q: 2. Give the reference bending design values for No. 1 Douglas Fir-Larch (DF-L) for the following…

Q: Solve Part 2 The timber shown below is standard dressed 8x12 Dense #1 Douglas Fir-Larch. This…

A: Section dimension:b=8"d=12"Live load WL = 8000 lbs

Q: A 12 × 12 column of Hem Fir, No. 1 grade, is 12 ft high andcarries a compression load of 12 kips…

A: Given 12×12 column of Hem Fir, No. 1 grade, is 12 ft high compression load of 12 kips. dead load…

Q: A two-span 3× 12 beam of Hem Fir, No. 1 grade, bearson a 3 × 14 beam at its center support. If the…

A: From table 5.1b. Reference design values for visually graded lumber of Hem Fir Member size=2.5 in.…

Q: Structural Analysis Question. Calculate the following, show working.

A: Please refer below pages.If you have any doubts please feel free to ask.Explanation:Step 1:Step…

Q: Rafters of Douglas fir–larch, No. 2 grade, are to be usedat 16 in. spacing for a span of 20 ft.…

A: Here in this question, we have to calculate the section modulus of the rafters, which can be…

Q: Design a single Hem-Fir select structural roof beam (plaster ceiling) which is expected to at least…

A: 2

Q: 2. Refer to Sketch #2 and assume a 250 #/SF design load on the decking (plywood) a. Determine…

A: Given data Load on plywood decking =250psf a.) The expression for linear load on 12'' wide strip of…

Q: A simple beam of hem fir select structural grade has a span of 18' with two concentrated loads of 4…

A: Given:- The span length of the simple beam of hem fir select structural grade = 18 ft The magnitude…

Q: 25- A wood beam is continuously supported on 5 shores. The load on beam is 2 Ib/ft' and the beam…

Q: Question 2: A residential building construction development is using columns that are 4.2m in…

A: Total load on the column = 50+30+10= 90KN Factored Load = 1.5*90= 135 KNE of western Hemlock wood=…

Q: Using the LRFD method, find the factored usable compressioncapacity (factored resistance) for the…

A: Given Section Nominal size, and grade (in.) Unbraced Length A 4×4 Douglas fir larch No.2 8 B…

Q: In attempt to construct a precast building, the structural engineer proposed a 5m width and a 7m…

Q: A Douglas Fir-larch 6x6 beam of No.1 Grade is 10 feet long and supports a total uniformly…

A: Douglas Fir-Larch Beam Size of beam=6 in×6 in Length of beam, L=10 ft=120 in Total uniformly…

Q: the size factor CF for a 6x8 douglas fir-larch no.1 is?

A: The size factor CF for a 6x8 Douglas Fir-Larch No.1 can be determined by referring to a lumber span…

Q: 10 ft long 6 × 10 simple beam of Douglas fir–larch, No. 2 grade, supports a uniformly distributed…

Q: A 10 ft long 6 x 10 simple beam of Douglas fir-larch, No. 2 grade, supports a uniformly distributed…

A: Given- A beam 10ft carrying a uniformily distributed load of 600lb/ft.Required- to check wheather…

Q: Ten-feet-high 2 × 4 studs of Douglas fir–larch, No. 1 grade, are used in an exterior wall. Wind load…

A: Given data: Height of wall=10 ft Exterior wall 2*4 studs Douglas fir-larch Wind load=25 psf Gravity…

Q: A 10 × 14 beam of Hem Fir select structural grade is loaded symmetrically with three concentrated…

A: To solve the problem, we will follow these steps: 1. Determine the Shear Force (V): - The beam is…

Q: Asimple beam ofHem Fir, select structural grade, has a spanof 18 ft with two concentrated loads of 4…

A: Schematic diagram of the given problem as per the statement:

Q: A timber beam is subject to a 15kN design point load applied at mid-span. If the beam is 120mm wide…

A: Design point load= 15 kNwidth= 120 mmdepth = 250 mmdesign strength = 8.5To find:allowable span

Q: What is the reference tension stress, Ft, for a 2x4 Douglas Fir-Larch (DF-L) No. 2 member?…

A: From NDS Supplement (National Design specification supplement) table 4A Ft for a 2x4 Douglas…

Q: The column supporting the glued laminated peams in the previous example is to be left exposed. A…

Q: span of Problem 5.4.C Rafters are to be used on 24-in. centers for a roof s 16 ft. Live load is 20…

A: The weight of an object is the force of gravity on the object and may be defined as the mass times…

Q: A short 4 x 4 square post made of Douglas Fir has an allowable compressive stress, F'. = 1000 psi.…

A: Given - 4' X 4' square post Allowable compressive stress, Fc' = 1000 psi

Q: Select square column sections of Douglas fir–larch, No. 1grade, for the following data:

A: In order to solve the problem here, we need not use any formulas rather we would use a axial…

Q: A 10× 14 beam of Hem Fir select structural grade is loadedsymmetrically with three concentrated…

A: As per the given data Due the symmetry RA = RB = 4300x32 = 6450lb SFD -

Q: A precast beam of length I is to be lifted at two points. The Two points should be at ________…

Q: Determine the maximum load that can be applied to an 8 X8, Hem-fir. Column is 24 ft long and is…

A: Draw the diagram From the above diagram the effective length along x-axis , kLx=24' Draw the…

Q: A 20-ft-span beam carries a dead load of 160 lb/ft anda live load of 240 lb/ft and is to consist of…

A: Given data Length, L=20ft=6096mm Dead load, DL=160 lb/ft=2.335kN/m Live load, LL=240 lb/ft=3.503kN/m…

Q: Determine the allowable load on a 3 m long layered built-up column made up of 6 nominal 2”x 6”…

Q: A 6× 12 beam of Douglas fir–larch, No. 1 grade, has 3 in. ofend bearing to develop a reaction force…

A: Solution: Bearing stress is given by Fb= Bearing ForceBearing Area ....... Equation (1)

Q: If the coefficient of friction between the steel wedge and the moist fibers of the newly cut stump…

Q: Determine the allowable load on a 3 m long layered built-up column made up of 6 nominal 2”x 6”…

A: Solution-The given values are as follows,The length (L) =3m=300mm6 nominal 2”x 6” piecesThe actual…

Q: 9.16 A 6X6 S4S Southern Pine (Dense No. 1) column is used to support headers that carry loads from…

A: The given data is shown below: 6×6 S4SE=1600 ksiFc=975 psi

Concept explainers

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.

Question

A 12 × 12 column of Hem Fir, No. 1 grade, is 12 ft high
and carries a compression load of 24 kips that is 9.5 in. eccentric from the
column axis. Investigate the column for combined compression plus bending
using the ASD method.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Design a Douglas fir-Larch No. 1 beam to support the load shown.
Check the cross-section for bending if the allowable normal stress is o =±120 MPa. a: + + 1 = 4 m a = 15 cm q = 3 kN/m a +
Pls ans asap
A residential building construction development is using columns that are 4.2m in hieght. The columns are made from seasoned Western Hemlock of Grade F14, with nominal dimensions of 190x45. Intermediate restraints are provided at 1.05m centres to minimize buckling about the minor axis. For the columns under consideration, intermediate restraints for minimizing buckling about the major axis are located at 2.1m centres. The columns can be considered as secondary members as they are closely spaced enabling load sharing. The columns carry unfactored compressive loads as follows: a permanent (dead) load of 50kN, an imposed (live) roof load of 30KN and wind load of 10KN. Assume that the imposed roof load is infrequent in nature (construction related) and that both the long-term inmposed (live) load factor (y) and combination factor for imposed action (W) are equal to zero. Location: Rockingham, Western Australia. Check the ability of the column to support the applied loads if the column is…
Using Douglas Fir larch, No. 2 Grade, pick the joist required if the live load is 40psf, the dead load is 20psf, deflection is limited to L/360, and joist spacing is 16 in on center with a span of 16?
a. Determine the allowable fiber stress in bending for a Douglas fir south select structural grade 2 Y4 for single and repetitive member use.b. What are the allowable spans for a Hem fir number 2, 2 ¥ 8 set at 12 in. o.c., 16 in. o.c., and 24 in. o.c.?
Ten-feet-high 2 × 4 studs of Hem Fir, No. 1 grade, are usedin an exterior wall. Wind load is 25 psf on the wall surface; studs are 16 in.on center; the gravity load on the wall is 500 lb/ft of wall length. Investigatethe studs for combined action of compression plus bending using the ASDmethod.
A simple beam has a span of 10 ft and supports a total uniformly distributed load, including its own weight, of 300 Ib/ft. Using Hem Fir, structural grade, determine the size of the beam with the least cross-sectional area on the basis of limiting bending stress.
A 6× 10 beam of Douglas fir–larch, No. 2 grade, has a total horizontally distributed load of 6000 lb. Investigate for shear stress.
A woode. Footbridge in a park has a span of 12 m between centers of end support .two logs of approximately constant diameter are to be used.eacg log must be capable of supporting a uniform load of 8 kN/m. If the allowable stresses is 8.3 MPa in bending.(a) What is the diameter of the log ? Round off the nearest tens
3) What is the allowable load capacity of a 5.5 in. x 9 in. glu-laminated timber column of Southern Pine when F-= 2520 psi, Cp = 0.9 and FCE= 705 psi?
Using Table 5.10, select joists to carry a live load of40 psf and a dead load of 10 psf on a span of 15 ft 6 in. Wood isDouglas fir–larch, No. 2 grade.