Design a Douglas fir-Larch No. 1 beam to support the load shown. F%1,300 psiF₁ = 85 psiVE = 1.6 × 106 psiAallow (LL)L/360WD=300#/PT. W₁ = 400#/FT.IIIL=16'F1

Answered: F% 1,300 psi F₁ = 85 psi V E = 1.6 ×…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Homework #8 60 #/' 12' fb = My/l = M/S fv=VQ/lb (general formula) fv=3V/2A (for rectangular sections) A 2x8 joist (b=1.5"; h=7.25") is loaded with a uniform load (w) of 60 #/ft on a simple 12' span. Determine the maximum bending stress (fb) and the maximum shear stress (fv) developed in the joist.
HW 3 Determine the column loads assuming: DL (decking, flooring, etc.) = 10 psf LL (occupancy) = 40 psf 50 psf Total Beam B-2 spans between girder G-3 and column B-2 and beam B-3 spans between girder G-3 and column C-2. K 10¹ G3 B GI OPEN B-2 DECKING Sad 8th of Makacals for Architecture and Buidhey Construction, 4adion Dry Ca 23 a G2 D DECKING) B-3 TYPICAL FLOOR FRAMING 2012, 2007 2002, 1999 by Pearson Higher Education, Inc Upper Bade River New Jersey 0745 Al Fogrs Reserved
Thanks in advance!
Determine the number of a glulam column 3.0 m in length that support an axial load of 120 kN. The column is to be built with 35mm thick and 200mm wide laminations of Yakal lumber (E = 9.78 GPa, Fc = 15.8 MPa). Assume a normal load duration, wet service condition and fixed-end connection with lateral support at both ends.
steel joist is spaced at 3’-0” oc and spans 35’-0”. It carries a dead load of 45 psf and a live load of 100 psf. What is the most economical steel joist able to carry this load? a. 24K7 b. 26K7 c. 28K7 d. 30K7
Using Douglas Fir larch, No. 2 Grade, pick the joist required if the live load is 40psf, the dead load is 20psf, deflection is limited to L/360, and joist spacing is 16 in on center with a span of 16?
a. Determine the allowable fiber stress in bending for a Douglas fir south select structural grade 2 Y4 for single and repetitive member use.b. What are the allowable spans for a Hem fir number 2, 2 ¥ 8 set at 12 in. o.c., 16 in. o.c., and 24 in. o.c.?
Using Douglas fir–larch, No. 2 grade, pick the joist size required from Table 5.10 for the stated conditions. Live load is 40 psf, dead load is 10 psf, and deflection is limited to L/360 under live load only.
Using Table 5.10, select joists to carry a live load of40 psf and a dead load of 10 psf on a span of 15 ft 6 in. Wood isDouglas fir–larch, No. 2 grade.

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

F% 1,300 psi F₁ = 85 psi V E = 1.6 × 106 psi Aallow (LL) L/360 WD=300#/PT. W₁ = 400#/FT. III L=16' F1