A 1:1:6 Mortar mix (by volume) has a W/C ratio of 1.20(by mass). The bulk density and relative density of the constituents are as follows: ОРС Lime Sand Bulk Density (kg/m³) Relative Density 1400 570 1650 3.15 2.26 2.65 How much (m³) mortar is produced with 25 kg of OPC? a. 0.0225 m³ b. 0.1092 m³ c. 0.2169 m³ d. 0.4521 m3

A 1:1:6 Mortar mix (by volume) has a W/C ratio of 1.20(by mass). The bulk density and relative density of the constituents are as follows: ОРС Lime Sand Bulk Density (kg/m³) Relative Density 1400 570 1650 3.15 2.26 2.65 How much (m³) mortar is produced with 25 kg of OPC? a. 0.0225 m³ b. 0.1092 m³ c. 0.2169 m³ d. 0.4521 m3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A concrete mix has a ratio os 1:2:4 by mass. The properties of the materials to be used are tabulated below. MATERIALS. SPECIFIC GRAVITY CEMENT 3.33 SAND 2.65 GRAVEL 2.67 Cement weighs 40 kg per bag. Use 24 liters of water per bag of cement Compute the volume of cement solids per bag of cement in cu m. Compute for the required volume of sand solids per bag of cement. Compute for the volume of concrete that can be produced per bag of cement 0.1 Need answer until 8 pm. Guaranteed like for a detailed complete solution.
A portland cement concrete mix requires mixing sand having a gradationfollowing the midpoint of the ASTM gradation band (Table 5.4) and gravelhaving a gradation following the midpoint of size number 467 of the ASTMgradation band (Table 5.5) at a ratio of 2:3 by weight. On a 0.45 power gradation chart, plot the gradations of the sand, gravel, and the blend. Is the gradation of the blend well graded? If not, what would you call it?
5.10 Samples of coarse aggregate from a stockpile are brought to the laboratory for determination of specific gravities. The following weights are found: Mass of moist aggregate sample as brought to the laboratory: 5,298 g Mass of oven dried aggregate: 5,216 g 5.11 5.12 5.13 5.14 Mass of aggregates submerged in water: 3,295 g Mass of SSD (Saturated Surface Dry) Aggregate: 5,227 g Find a. The aggregate bulk dry specific gravity b. The aggregate apparent specific gravity c. The moisture content of stockpile aggregate (report as a percent) d. Absorption (report as percent) Base course aggregate has a target dry density of 1917 kg/m³ in place. It will be laid down and compacted in a rectangular street repair area of 600 m × 15 m × 0.15 m. The aggregate in the stockpile contains 3.1% moisture. If the required compaction is 95% of the target, how many tons of aggregate will be needed? Calculate the percent voids between aggregate particles that have been com- pacted by rodding, if the…
The requirements and material properties of an air entrained concrete mix are given below. Calculate the weights of the components of 1 m3 of concrete. Water content: 200 kg/m3 Air content: 7.5% W/C: 0.45 (By Weight). Dry aggregate volume in 1 m3 concrete mixture: 0.44 m3 Specific Gravity (g/em3 ) water absorption capacity (%) Total Moisture (%) Cement 3.15 Fine aggregate (saturated surface dry) 2.65 1.3 5.5 Coarse aggregate (saturated surface dry) 2.7 0.5 1.5 Dry unit weight of coarse aggregate is 1,500 kg / m3. 'kind
Suppose that the following mix design was obtained at the lab before making any field adjustments for aggregate moisture content: kg/m³ Cement 307.4 | 43.5 Fly ash Water | Coarse aggregate (SSD) | 1019.7 Fine aggregate (SSD) 193 781.1 Further suppose that the aggregates have the following properties: |(by mass) Coarse aggregate Fine aggregate Absorption Capacity 0.5 % Moisture Content 0.3 % 0.9 % 1.3 % a) Determine the moisture state of the coarse and fine aggregates. (i.e. wet, SSD, or air dry) b) Calculate the field mix design weights (show your calculations): Field kg/m³ Cement Fly ash Water ? Coarse aggregate (SSD) Fine aggregate (SSD) ?
8) For the following cements, answer the following questions: Cement A Cement B C3S (%) C2S (%) СЗА (%) Alkalis (%) SO3 (%) CaCO3 (%) Blaine fineness (m²/kg) Loss on ignition (%) Insoluble residue (%) *Other aspects of the cements are comparable to each other. 60 50 15 20 10 6 1 1 2.5 2.5 5 1 350 300 0.01 0.75 3 0.1 a) Which cement has high early strength? Briefly explain. b) Which cement would you use in an emergency repair? Briefly explain. c) Which cement would you use in a small retaining wall during a hot summer? Briefly explain. d) Which cement has higher sulfate resistance? Briefly explain. e) Which cement is stored improperly? Briefly explain f) During the production of which cement, the kiln reactions were almost complete? Briefly explain
4 pts Question 23 What is the fineness modulus of this aggregate? % Cumulative Retained Retained Mass 0% Sieve Size (US) (g) Retained Passing 1" 3/4" 1/2" 3/8" # 4 650 18.3 700 19.7 632 17.8 175 4.9 # 8 200 5.6 #16 W 150 4.2 #30 125 3.5 #50 331 9.3 #100 288 8.1 #200 250 7 Pan 50 1.4 Total 3551 O 5.20 O 1.57 O 3.89 O 6.50
The table below shows the properties of materials required to design a concrete mix. It is required to:a- Make a complete mix design.b- Express the proportions by volume for water, coarse aggregate, and fine aggregate, knowning that weight of 1 m3 gravel = 1760 kg/m3 and weight of 1 m3 sand = 1600 kg/m3.c- From the designed mix it is required to make a trial mix enough for six standard cubes (15 cm x 15 cm x 15 cm), six standard cylinders (d = 15 cm, h = 30 cm), and three standard beams (15 cm x 15 cm x 70 cm). what are the proportions of this mix? Using BSI Method only
For a design a concrete mix which is going to be used in Muğla the 28-day compressive strength of the concrete is required to be 30 MPa and slump of the fresh concrete is specified as 8-10 cm. Maximum size of the aggregate is 25 mm. Other necessary data are given as: Specific gravity of cement = 3.1 Bulk specific gravity of coarse aggregate = 2.68 Bulk specific gravity of fine aggregate = 2.64 Absorption capacity of both aggregates is 1.5% Fineness modulus of fine aggregate = 2.8 Dry rodded unit weight of the coarse aggregate = 1600 kg/m³ According to ACI 211 and based on absolute volumes: What should be the weight of SSD coarse aggregate in kg's? What should be the amount of mixing water in kg's? What should be the water to cement ratio? What should be the volume of dry rodded coarse aggregate per unit volume of concrete? What should be the air content in 96? What should be the SSD weight of fine aggregate in kg's? Seç Seç... Seç Seç... # Seç + Seç... # # + ÷
If needed assume the unit weight of water to be 62.4 lb/ft3 a) A HMAC sample has the following volumetric properties (i) VMA = 0.1865 ft3and (ii)Volume of air = 0.0452 ft3 Compute %VFA. b) A HMAC sample has 140 lbs of aggregate with a bulk specific gravity of 2.65 and aneffective specific gravity of 2.71. Based on this information the volume of the absorbedasphalt is ________________ft3A compacted sample of hot mix asphalt concrete sample has a unit weight of 135 lb/ft3.c) The sample has an asphalt content of 5% (by weight). Assume no absorbed asphalt.The bulk specific gravity of the aggregate is 2.65, and specific gravity for the asphaltcement is 1.05. Based on this information compute VMA for this mixture.
A concrete mix has the following ratio, excluding water, of cement:sand:gravel (3:6:7). How much gravel would be needed in 860 cubic meters of the dry mix? Round your answer to the nearest whole number.
The cement content of a concrete is 375 kg/m3 and the w/c ratio is 0.46. At a specific moment of the cement hydration, the degree of hydration is 0.80. Calculate the volume (dm/m³) of the following: (i) chemically bound water, (ii) gel water and (iii) capillary water A concrete sample was extracted from a structure and dried at 105 °C in which 80 kg/m3 of water evaporated. The degree of hydration (a) was determined to be 0.5. The mix design of the concrete was 1:6.0:0.6 (Cement:Aggregates:Water mix ratio by weight) and the target air content was 3 %. a) How much of the water had been evaporated prior to drying at 105°C? b) What were the volume of (i) un-hydrated cement, (ii) solid part of cement gel, (iii) gel water, (iv) contraction pores, and (v) capillary pores at the time of sampling?