A 111- resistor, a 0.150-uF capacitor, and a 5.77-mH inductor are connected in series to agenerator whose voltage is 27.8 V. The current in the circuit is 0.150 A. Because of theshape of the current-versus-frequency graph (shown), there are two possible values forthe frequency that correspond to this current. Obtain these two values. Give (a) thesmaller value, and (b) the larger value. Note: The ac current and voltage are rms values andpower is an average value unless indicated otherwise.

Answered: Image /qna-images/answer/3b16d193-6787-4435-8e66-2dfd44571560.jpg

Answered: A 111- resistor, a 0.150-uF capacitor,…

Sustainable Energy

2nd Edition

ISBN:9781337551663

Author:DUNLAP, Richard A.

Publisher:DUNLAP, Richard A.

Chapter19: Battery Electric Vehicles (bevs)

Section: Chapter Questions

Problem 16P

See similar textbooks

Similar questions

Handwritten.
For the following equilibrium system, assuming all strings are ideal. If the mass M = 50, and the angles B and 0 are 50 ° and 30, respectively. What is the value of the magrnitude of the voltage T4? a) T = 762.3042 N b) T = 980 N c) T, = 565.8035 N d) T=639.6499 N
Find the magnitude and direction in X and Y of the motion of the joint at point C of the flat truss supporting a load of 1000 N as shown in the figure below. The value of E=210GPA for each member, the elements have a circular section with an external diameter of 75 mm and a thickness of 5 mm. Use the work and energy method. (In the picture it says 10 but it's 1000) E D B 1920 mm 1080 mm ION 810 mm 1440 mm
3) The apparatus shown below is made of a tungsten bar AC and the magnesium bar BD that are attached to a pointer CDP by pins at C and D. Let the coefficients of thermal expansion for magnesium and tungsten be denoted by Am and C,, respectively. Derive a formula for the vertical displacement O (positive upward) of point P due to a uniform temperature increase Ar. Could such a device be used as a thermometer? ΔΤ B
21:19 40 A 9 41%- Chegg Home Expert Q&A My answers ( Civil Engineering Question The rope ABexerts a 46 - N force T on the collar at A Let rCA be the position vector from point Cto point A (Figure 1) Figure You answered Bo P1 II
The sinusoidal waveform of an ac circuit shows that the: <-90% O the current is leading the applied voltage by 90 O applied voltage is leading the current by 90 O applied voltage is lagging the current by 90 applied voltage is in phase with the current
8. A belt conveyor is used to deliver a fluid to a reservoir, see the figure. The depth of the fluid film on the belt is such that the velocity on the free liquid surface of the film is zero. By considering only the work done by the belt on the fluid in shear, find the efficiency of this device. Engi eprt an sity
A cantilever beam model is often used to represent micro-electrical-mechanical systems (MEMS) (see figure). M Cantilever beam Electrode Dielectric substrate Polysilicon anchor The cantilever beam is made of polysilicon (E = 150 GPa) and is subjected to an electrostatic moment M applied at the end of the cantilever beam. If dimensions are b = 1.5 pm, h = 4.3 pm, and L = 300 pm, find expressions for the tip deflection and rotation of the cantilever beam in terms of moment M. (Use available deflection formulas. The beam has constant flexural rigidity EI. Enter the coefficient for M in N-1 for tip deflection and in Num-1 for tip rotation. Enter the magnitudes.) tip deflection M tip rotation M
A 21-mm-diameter steel [E = 191 GPa; α = 11.8 x 10-6/°C] bolt is used to connect two rigid parts of an assembly, as shown in the figure. The bolt length is a = 155 mm. The nut is hand-tightened until it is just snug (meaning that there is no slack in the assembly, but there is no axial force in the bolt) at a temperature of T = 48°C. When the temperature drops to T = -13°C, determine(a) the clamping force that the bolt exerts on the rigid parts (positive if in tension and negative if in compression).(b) the normal stress in the bolt (positive if in tension and negative if in compression).(c) the normal strain in the bolt (positive if it stretches and negative if it shrinks).
It's urgent Please solve immediately
no 7
The block shown in Figure 2 is subject to three forces. a) Determine the normal voltage at point A. b) Determine the normal voltage at point B. DICE: b = 100mm; b ’= 50mm; d = 75mm; d '= 125mm; P1 = 500N; P2 = 1250N; P3 = 250N. Disregard the weight of the block. Please show me step by step

SEE MORE QUESTIONS

Recommended textbooks for you

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Engineering Fundamentals: An Introduction to Engi…

Civil Engineering

ISBN:

9781305084766

Author:

Saeed Moaveni

Publisher:

Cengage Learning

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Engineering Fundamentals: An Introduction to Engi…

Civil Engineering

ISBN:

9781305084766

Author:

Saeed Moaveni

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS