Need the answer in 15 mins. A 0.4 kg rubber ball has a horizontal velocity of 1.554 m/s at point A and goes through aprojectile motion until it hits a smooth floor at point B. It then bounces off and reachesanother peak in its trajectory at point C.AVo|st1.3 m0.8 mB4.81 m/s5.17 m/s1.554 m/s5.28 m/s+сi2. Which of the following best approximates the SPEED of the ball right before it hits thefloor at point B?hsmooth floor with an impact which has a coefficient of restitution of 0.8 inin of time.

According to the given dataWe need to findThe velocity of the ball when hits the ground

A 0.4 kg rubber ball has a horizontal velocity of 1.554 m/s at point A and goes through a projectile motion until it hits a smooth floor at point B. It then bounces off and reaches another peak in its trajectory at point C. A V 1.3 m B с h 0.8 m i 2. Which of the following best approximates the SPEED of the ball right before it hits the floor at point B?

A 0.4 kg rubber ball has a horizontal velocity of 1.554 m/s at point A and goes through a projectile motion until it hits a smooth floor at point B. It then bounces off and reaches another peak in its trajectory at point C. A V 1.3 m B с h 0.8 m i 2. Which of the following best approximates the SPEED of the ball right before it hits the floor at point B?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

can please help me understand how someone could possibly do 75 windmills in a minute?? with madeup calculations please??
3
We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical milling machine and 50 cm from the edge. The width of the slot is 40 mm. TheDepth of the slot is 25 mm. For this, several rough cutting steps and aFine cut with a depth of 0.20 mm. The depth for each of the steps ofrough cut is limited to 1.75 mmAditional information:What is the number of blades used for the rough cutting steps?What is the number of blades used for the fine cutting step?
Hello, I was just wondering how you find hte angle of the blocks to 45 degrees? Thank you!
In a lathe machine, The diameter of the driver and driven pulley are 2745 mm and 1200 mm respectively, And the driver pulley runs at speed of 225 rpm. Find the speed at which is driven pulley runs in the machine. the speed of the driven pulley in rpm is
What would a .010 - .020 cutback of a 14.500 Diameter be?
Solve it fast
2) A washer is going to be manufactured by cutting operation out of 2024ST aluminum alloy sheet that has a thickness of 2.5 mm. The outside diameter of the washer is 25.0 mm, and the inside diameter is 12.0 mm. Make a rough sketch, define the geometries to be used and determine a. The punch and die size for the blanking operation b. The punch and die size for the punching operation c. The force required performing the blanking and punching operation simultaneously. The aluminum has a tensile strength = 300 MPa.
I need answer within 20 minutes please please with my best wishes
Q1. The part shown below will be turned in two machining steps. In the first step a length of (50 + 50) = 100 mm will be reduced from Ø100 mm to Ø80 mm and in the second step a length of 50 mm will be reduced from Ø80 mm to Ø60 mm. Calculate the required total machining time T with the following cutting conditions: Cutting speed V=80 m/min, Feed is f=0.8 mm/rev, Depth of cut 3 mm per pass. Ø100 Ø80 Ø60 50 50
16)
Find lx and ly.. Urgent...please do in 15 minute's