9. A uniform 400 N boom is supported as shown in the figure below. Fixl the tension in the tie rope and the förce exerted on the boon by the pin at P. L4 3L4. 2000 N 50 .......

Q: A 8.00 m long 20.0 kg bar is attached to a wall by a hinge on its right end. An unknown mass hangs…

A:

Q: The figure shows the forearm of a person holding a book. The biceps exert a force FB to support the…

A:

Q: A mobile crane has a 25 ft long boom (OA). The center of gravity (G1) of the boom is located at its…

A:

Q: 5. If the maximum tension that the string can withstand is 4200N, what is the maximum mass that can…

A:

Q: A uniform 312 kg boom is 10.0 m long is held up by cable attached 6.00 m from the wall at an angle…

A: Given: The mass of the boom is m=312 kg, The distance of cable from wall is PQ=6 m, The length of…

Q: D CU... t ona- t Pool ment..... 25,551 80 3 5. A 1.90 kg box rests on a plank that is inclined at an…

A: Given data :  Mass of box m = 1.90 kg  Force constant of spring k = 25 N/m  Static friction between…

Q: The boom in the figure below (Figure 1) weighs 2850 N and is attached to a frictionless pivot at its…

A:

Q: 7. A uniform ladder of mass (m) and length (L) leans against a frictionless wall, see figure. If the…

A: The mass of the ladder: The length of the ladder: The inclination angle: The coefficient of static…

Q: 31. Shear force equation for segment BC. * a. 7.35KN-0.15x2(KN/m2) b. 7.26KN-0.18x2(KN/m2) c.…

A:

Q: A sign is supported by a uniform horizontal boom of length 3.00 m and weight 80.0 N. A cable,…

A: What is the vertical force Fy exerted on the boom by the hinge. Given,   θ=34.9oweight of…

Q: As shown below, on Triton a 9 kg beam of length L is leaning against a frictionless wall and is in…

A:

Q: An exhaust system for a pickup truck is shown in the figure. The weights Wh, Wm, and w, of the…

A: SOlution: Given that

Q: Determine the forces in members BC and BH of the loaded truss. 1480 Ib, 26° 1030 lb. 19 15' E B 780…

A: Given: The diagram is as follows: Introduction: A force is a push or pull upon an object resulting…

Q: A plank L m long is placed in a horizontal position with its ends resting on two inclined planes as…

A: Solution:-

Q: Draw shear force and bending moment diagram of the beam shown in figure 1 for the gives loadino.…

A: The objective of the question is to draw the shear force and bending moment diagram for the given…

Q: A board of mass mand length l is attached to a wall and a rope that makes an angle of theta, as…

A: Free-body diagram

Q: A 5-m weightless strut, hinged to a wall is used to support a 1189 N block as shown. Determine the…

A: Given Strut length AB = 5 m Weight W          = 1189 N Determine the vertical component of the force…

Q: A cook holds a 2.01-kg carton of milk at arm's length (see the figure below). What force F must be…

A:

Q: number 1

A: a) If the first condition of the equilibrium is not satisfied then it means that the total force is…

Q: 72. Go Review Conceptual Exam- ple 7 before starting this prob- lem. A uniform plank of length o 5.0…

A:

Q: number 4

A:

Q: A 10 800-N shark is supported by a rope attached to a 5.00-m rod that can pivot at the base. 20.0…

A:

Q: The 20kg flowerpot is supported at A by the three cords. (a) Determine the magnitude of the force…

A: Given Flowerpot mass = 20 kg  Determine the magnitude of the force acting in cord AB,AC,AD for…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A: The free-body diagram of the system is shown below.

Q: A spring with a spring constant k = 852 N/m is compressed from its unstretched length to a length of…

A: The potential energy of the spring is given by 0.5kx^2            where k= spring constant…

Q: You are hanging a heavy picture on a wall, using a wire attached to the top corners of the picture.…

A: Tension is a force applied on an wire or a string by an object when the object is placed over the…

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).